Cheetah
Installation Guide
Disc Drive
ST136403LW/LC
Contents
Preface
Always handle the drive by its edges or frame
Handling precautions
Electrostatic discharge protection
Important safety information and precautions
Always observe the following warnings and precautions
Wichtige Sicherheitshinweise
Page
chädigung der Komponenten und Erlöschen des Garantieanspruchs führen
Electromagnetic compliance
Regulatory agency compliance
Electromagnetic susceptibility
Australian C-Tick
Electromagnetic compliance for the European Union
Figure 1. Cheetah 36 family drive LW model shown
General description
The primary benefits of LVD technology
Single-ended and low voltage differential modes
Providing adequate cooling
SE and LVD bus configurations
Data bus widths
Kühlung des Systems
Abbildung 2. Empfohlener Luftstromverlauf
Figure 2. Suggested air flow
Above unit Under unit
Above unit Under unit
Asynchronous data transfer rate
Characteristics
ST136403LW/LC
LVD mode
DC power requirements ±5%1 +5
Low voltage
Single-ended SE
1. Set the SCSI ID on the drive
How to install the drive
LW model installation
Drive Front
Figure 3. Setting the SCSI ID on LW model drives
2. Configure termination
Cheetah 36 Installation Guide, Rev. A
Figure 4. SCSI bus termination
Figure 5. Setting terminator power jumpers
3. Configure termination power
4. Connect the drive activity remote LED optional
Figure 6. Drive Active LED indicator connections
Note On some LEDs the flat side of indicator is cathode
Reserved Activity LED Reserved
Delay Motor Start and Motor Start options
Single-ended mode option
Write Protect option
Parity Check option
Pin Pin
Figure 7. Additional jumper options
R R S D M W P E E T E S E P D S S P
7. Format the drive
6. Mount the drive in the host system and connect cabling
Cheetah 36 Installation Guide, Rev. A
Figure 8. Connecting cables to the drive
1 “X” means up to 15 devices on the SCSI bus
Figure 9. Multiple-drive connection to host adapter
Dimension Table
Figure 10. Mounting configuration dimensions LW model
Figure 11. Alternate SCSI ID select and LED connection
Additional connector on LW model drives
1. Set the SCSI ID on the drive
LC model installation
Drive Front
Figure 12. Setting the SCSI ID on LC model drives
Cheetah 36 Installation Guide, Rev. A
LC model drives are designed for installation in host sys- tems that have a backplane with single connector attach- ment SCA connections. Termination is normally provided on this backplane. Check your host system documentation for details
2. Configure termination
Delay Motor Start and Motor Start options
Single-ended mode option
Write Protect option
Parity Check option
Cheetah 36 Installation Guide, Rev. A
Figure 13. Additional jumper options
80-pin SCSI I/O Connector Pin J2 J6
4. Mount the drive in the host system
Figure 14. 80-pin I/O connection to drive LC model
Max screw penetration into side of drive
Figure 15. Mounting configuration dimensions LC model
Dimension Table
Important information about formatting the drive
5. Format the drive
Drive partitioning
DOS, Windows 3.1, Windows 95, and Windows
System preparation
Drive formatting
Macintosh
Online Services
Seagate Technology support services
Automated Services
Internet
Seagate Express
Presales Support
Technical Support
USA/Canada/Latin America Support Services
Customer Service CSO
Warranty Repair
Authorized Service Centers
Call Center
European Support Services
MA Informatica
Memofix
Asia/Pacific East Support Services
Africa/Middle East Support Services
Fax Services-All European Countries
SeaBOARD
FAX +81-3-5462-2979
SeaFAX
Warranty Repair
Page
Page
Page
920 Disc Drive, Scotts Valley, CA 95066-4544, USA
Publication Number 83329450, Rev. A, Printed in USA
Seagate Technology, Inc