General DC power requirement notes | Seagate ST31000640SSIM instruction

[4]This condition occurs after OOB and Speed Negotiation completes but before the drive has received the Notify Spinup primitive.

[5]See paragraph 6.2.1, "Conducted noise immunity." Specified voltage tolerance includes ripple, noise, and transient response.

[6]During idle, the drive heads are relocated every 60 seconds to a random location within the band from three-quarters to maximum track.

General DC power requirement notes.

1.Minimum current loading for each supply voltage is not less than 1.7% of the maximum operating current shown.

2.The +5V and +12V supplies should employ separate ground returns.

3.Where power is provided to multiple drives from a common supply, careful consideration for individual drive power requirements should be noted. Where multiple units are powered on simultaneously, the peak starting current must be available to each device.

4.Parameters, other than spindle start, are measured after a 10-minute warm up.

5.No terminator power.

6.2.1Conducted noise immunity

Noise is specified as a periodic and random distribution of frequencies covering a band from DC to 10 MHz. Maximum allowed noise values given below are peak-to-peak measurements and apply at the drive power connector.

+5V	=	250 mV pp from 0 to 100 kHz to 20 MHz
+12V	=	800 mV pp from 100 Hz to 8 KHz
		450 mV pp from 8 KHz to 20 KHz
		250 mV pp from 20 KHz to 5 MHz

6.2.2Power sequencing

The drive does not require power sequencing. The drive protects against inadvertent writing during power-up and down.

6.2.3Current profiles

The +12V and +5V current profiles are shown below in figure 2.

Note: All times and currents are typical. See Table 2 for maximum current requirements.

Barracuda ES.2 SAS Product Manual, Rev. G

25

Image 31

Seagate ST31000640SSIM General DC power requirement notes, Conducted noise immunity, Power sequencing, Current profiles

Contents

ST31000640SS ST3750630SS ST3500620SS Barracuda ES.2 SASPage General description Performance characteristicsReliability specifications Physical/electrical specifications Installation Defect and error managementInterface requirements Seagate Technology Support Services Barracuda ES.2 SAS Product Manual, Rev Scope Barracuda ES.2 SAS Product Manual, Rev. G Electromagnetic susceptibility Standards, compliance and reference documentsStandards Electromagnetic compatibility Compliance Reference documents Barracuda ES.2 SAS Product Manual, Rev. G Barracuda ES.2 drive illustration General description Reliability Standard featuresMedia description Performance Formatted capacities Factory-installed optionsProgrammable drive capacity Barracuda ES.2 SAS Product Manual, Rev. G Seek performance Performance characteristicsInternal drive characteristics Access time General performance characteristics Format command execution time minutesStart/stop time Cache operation Prefetch/multi-segmented cache controlCaching write data Prefetch operation Unrecoverable Errors Reliability specificationsError rates Recoverable Errors Preventive maintenance Reliability and serviceSeek errors Interface errors Reporting control 4 S.M.A.R.TControlling S.M.A.R.T Performance impact Predictive failures Temperature Log Page 0DhThermal monitor Invoking DST State of the drive prior to testingDST failure definition Implementation Log page entries Product warrantyShort test Function Code 001b Extended test Function Code 010b Product repair and return information Shipping Barracuda ES.2 SAS Product Manual, Rev. G ST31000640SS DC power requirements Physical/electrical specificationsAC power requirements DC power requirements ST3500620SS DC power requirements ST3750630SS DC power requirements Current profiles General DC power requirement notesPower sequencing Conducted noise immunity Typical ST31000640SS drive +5V and +12V current profiles Typical ST3500620SS drive +5V and +12V current profiles Power dissipation Barracuda ES.2 SAS Product Manual, Rev. G Environmental limits Temperature a. Operating Shock Relative humidityEffective altitude sea level a. Operating Shock and vibration Package size Packaged/product weight Drop height Corrosive environment Air cleanlinessVibration a. Operating-normal Acoustics See Section Barracuda ES.2 SAS Product Manual, Rev. G Physical dimensions Mechanical specifications Drive internal defects/errors Defect and error managementDrive error recovery procedures 108.29 Background Media Scan SAS system errorsMedia Pre-Scan Idle Read After Write Deferred Auto-Reallocation Drive orientation Installation Air flow Cooling Grounding Drive mounting Barracuda ES.2 SAS Product Manual, Rev. G Interface requirements SAS features Dual port support Commands supported by Barracuda ES.2 SAS family drives Scsi commands supportedCommand name Command code Supported Commands supported by Barracuda ES.2 SAS family drives Commands supported by Barracuda ES.2 SAS family drives Commands supported by Barracuda ES.2 SAS family drives Inquiry data Mode Sense dataBarracuda ES.2 SAS inquiry data Bytes Data hex Page Mode Pages 2.1 ST31000640SS Mode Sense data 2.2 ST3750630SS Mode Sense data 2.3 ST3500620SS Mode Sense data Miscellaneous status Miscellaneous operating features and conditionsMiscellaneous features Supported Feature or condition SAS physical interface Datum B Connector requirements Physical characteristics SAS pin descriptions Pin Signal name Signal typeElectrical description Pin descriptions Ready LED Out Signal characteristicsPower SAS transmitters and receivers Eye masks Eye masks overview LED drive signalDifferential signals General interface characteristics Normalized time in UI Receive eye maskJitter tolerance masks Absolute amplitude Frequency in kHz Peak-toSinusoidal Jitter Signal characteristica Units Gbps Transmitter signal characteristics Gbps m, n Deterministic jitterq Receiver signal characteristicsSignal characteristic Units Gbps Maximum allowable jitter Impedance requirements Sheet 1 Impedance specificationsReceiver jitter tolerance Compliant jitter test pattern Cjtpat Impedance requirements Sheet 2 Transmitter characteristicsElectrical TxRx connections = -5,437dB Shows the zero-length test load Receiver characteristics Barracuda ES.2 SAS Product Manual, Rev. G