Drive mounting, Ultra ATA/100 cable | Seagate ST3750840ACE manual

3.3.3Ultra ATA/100 cable

An 80-conductor 40-pin cable is required to run Ultra DMA mode 3, mode 4, and mode 5. This cable uses even-numbered conductors connected to the ground pins to improve signal integrity.

Master

Slave

Note.

Pin 1

Computer

Motherboard

If you are using a 40-pin, 80-conductor cable, attach the blue connector to the motherboard, the black connector to the master drive, and the gray connector to the slave.

Figure 5 Ultra ATA cable connectors

Note. The drive supports both host and drive cable detection. The host detects the 80-conductor cable by sampling pin 34, CBLID–, on the interface bus. The drive detects the 80-conductor cable by sens- ing a capacitor at the host side through the CBLID– signal. The result is reported in a Fast Rise Detected bit (bit 13 of word 93 in the Identify drive parameter block).

3.4Drive mounting

You can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the bottom-mounting holes. See Figure 6 for drive mounting dimensions. Follow these important mounting precau- tions when mounting the drive:

•Allow a minimum clearance of 0.030 inches (0.76 mm) around the entire perimeter of the drive for cooling.

•Use only 6-32 UNC mounting screws.

•Do not overtighten the mounting screws (maximum torque: 6 inch-lb.).

•Do not use a drive interface cable that is more than 18 inches long.

24	DB35.3 Series PATA Product Manual, Rev. B

Image 30

Seagate ST3750840ACE manual Drive mounting, Ultra ATA/100 cable

Contents

DB35.3 Series Pata Page Contents DB35.3 Series Pata Product Manual, Rev. B List of Figures DB35.3 Series Pata Product Manual, Rev. B Introduction DB35.3 Series Pata Product Manual, Rev. B Drive specifications Specification summary table Drive specification ST3750840ACE ST3500830ACE ST3400820ACE DB35.3 Series Pata Product Manual, Rev. B Drive specification ST3320820ACE ST3300820ACE ST3250820ACE DB35.3 Series Pata Product Manual, Rev. B Formatted capacity Default logical geometryLBA mode Cylinders Read/write heads Sectors per track 16,383 Recording and interface technology Physical characteristicsDrive specification 750GB 500GB 400GB 320GB 300GB 250GB Power specifications Seek timeStart/stop times Standby mode DC power requirements Typical current profile Conducted noise Idle mode Power-management modesActive mode Sleep mode Environmental specifications Nonoperating shock Disc models ShockOperating shock 4 Disc models Acoustics Fluid Dynamic Bearing FDB motor acousticsIdle CE seek profile Reliability Safety certificationElectromagnetic immunity Agency certification Australian C-Tick N176 Electromagnetic compatibilityKorean RRL FCC verification Environmental protection Corrosive environmentEuropean Union Restriction of Hazardous Substances RoHS DB35.3 Series Pata Product Manual, Rev. B Configuring and mounting the drive Handling and static discharge precautions Breather filter hole precautions Breather filter hole location Drive as master with a non-ATA-compatible slave Jumper settingsMaster/slave configuration Cable-select option Drive mounting Ultra ATA/100 cable Mounting dimensions-top, side and end view DB35.3 Series Pata Product Manual, Rev. B ATA interface signals and connector pins Pins and supported ATA signalsATA interface Supported ATA commands Command name Command code in hex F4H Identify Device command Word Description Value Xx07H Description if bit is set to Bit Word Bit Word Set Features command 0CH 4 S.M.A.R.T. commands Code in features Register A.R.T. command Presales Support Seagate Technology support servicesInternet Technical Support Warranty Service Data Recovery Services Authorized Service CentersData Recovery Services Call Center Toll-free Direct dial Index Page TMR DB35.3 Series Pata Product Manual, Rev. B Page Seagate Technology LLC