Contro green, Satin stitch | Sears 385. 1884180 specification

Set the Machirt_

Stitchw_dth

control 3 to 6

I

Top thread tension control 3 to8

co

Stitch length

contro_ green

ZOn_

F:Satin stitch

foot	Stretch Stitch

The Stitches and The,r Uses

These stitches are pu rely decorative.

You can sew one row or severa[ or vary the stitch width and length for

special effects.

Experiment on a scrap of fabric to see what spemal effects are possible.

Here's How

1. Adjust the stitch width and length as you desire.

2.Practice the stitch on a scrap of fabric.

3.Mark the lines for decoration on the fabric, using a washable fabric marker.

4.Lower the needle at the starting point.

5.Lower the presser foot.

6.Gentty guide the fabric atong the maked line.

6O

Image 62

Sears 385. 1884180 owner manual Contro green, Satin stitch

Contents

Sewing Machine Sears Canada NC Kenmore Sewing Machine Table of Contents Know Your Machine Portable Case or Cabinet is AvailablePage Bobbin Plug in the Machine and Switch on the Power OFF Pressure Dial should Reset at Machine is running = Thread Cutter = Setting Spool Pins= Adjust the Presser Foot Lever Foot = Free-Arm Sewing the Removable Extension Table To remove Oranycirculargarmentarea Orareasofwearinchildrensclothes Etc To Attach Changethe Presser Foot Zigzag Foot To Snap OnPresserFoot Types Zipper Edges Sliding Buttonhole FootUse this Guide Qu liter Topstitching = Presser Foot TypesButtonhole Foot FabNcs Check Your Needle To Change Your Needle Onto = To Remove the Bobbin from the Machine = Wind the BobbinPut Pin With Thread Winding Direction Insertthe Bobbin into the Bobbin Hotder Thread Your Needle Pick Up Your Bobbin Thread Toward Inches Adjust the Top Thread Tension Top Is set Indicator panelTop tension Too Tight Too Loose Is up Stremh Stitch Position = Three Needle PositionWidth Needle position Three Needle Position Sem On p Check ChartII1 III Refer to 52 ~ 3N6 Stitch Shell On p.15 Onp Stitch Refer to On p 155 ZoneCheck Turn a Square Corner Control 0 grog Use the Darning PlateUse the darning plate in the following ways Thread tension Center Out Control orangeControl 2 to Plate and replace foot holder and foot When you finish darning, remove the darningHeresHow Basle Zigzag Set the Machine Contro I to Contro 3 to Very short Applique= Bar Tacking Pressure dial2 Embroidery Zigzag foot Darning plate Sew a Button=dth control = Rick-Rack Stretch Stitch length Control Three-Step Zigzag Stitch width control 5 to Sat the Machine Overcast Stretch StitchingSarging or Pine Leaf Stretch Stitchin Zi£rzegfoot Weight Set the Machine Stitch width Control Light Ilili!!ii!iiilji Cuffs = Learningto Sew ButtonholesHave Or where 31controt Stitch wdthControl 3 to Controt 2 toPage Buttonhole foot Pins a Lever Buttonhole Marked buttonhole End ol opemng Openthezipper Cosethe zipper and turn Control 3 to 8Stitch Iength control orange zone Set the Machine Stitch widthLingerie Smocking Control 3 to 6 2 Zigzag foot Stlchwidth control 3 to Zigzag toot Iii¸!iiiiii¸...........i Positron Stitch width control 3 toStitch length controt Contro green Satin stitch Whatto do when Improper IncorrectInsert Vacuum Cover plate by Driver Parts List 813404013 B868102403202 655t 1920 Overedge foot 13, 27, 40, 42 Parts list 6566 PerformancePlug connector Portable Buttonhole Making 4551 Opener Template 6566 Two-point Box Zipper Application 5253 Foot T2, 26 6566 Settingupyourmachine Stitch SelectorPage Practical Stitch Chart FAGOT,NG Warranty Year Visit Sewing Machine385