Machine is running | Sears 385. 1884180 specs

Set the Pressure Dial

j

Your machine has two ranges of speed--a low work and a high one for faster, general work. On

will sew no faster than approximately two4hird even when the foot control is fully depressed.

range for slower, intricate the low setting the machine the speed of the high one,

Setting mark

NOTE: It is advisable not to change the speed range switch while

machine is running.

The pressure control dial is located inside the face cover plate,

Set the dial aligning the setting mark on the dial with the groove as follows.

3	most	sewing
2	applique		and Cut-Out		work
1	basting,		sewing	chiffon,	lace,		organdy	and other lightweight	fabrics.
	Also	for	vetours and knits			(with more		stretch),
NOTE:	The	pressure		dial should		be	reset at	3 after changing pressure, so

the machine is ready for most normal sewing the next time you use

it.

Image 8

Sears 385. 1884180 owner manual Machine is running, Pressure Dial should Reset at

Contents

Sewing Machine Sears Canada NC Kenmore Sewing Machine Table of Contents Know Your Machine Portable Case or Cabinet is AvailablePage Bobbin Plug in the Machine and Switch on the Power OFF Pressure Dial should Reset at Machine is running = Setting Spool Pins = Adjust the Presser Foot Lever= Thread Cutter Foot = Free-Arm Sewing the Removable Extension Table To remove Oranycirculargarmentarea Orareasofwearinchildrensclothes Etc To Attach Changethe Presser Foot Zigzag Foot To Snap OnPresserFoot Types Sliding Buttonhole Foot Use thisZipper Edges Guide Qu liter = Presser Foot Types Buttonhole FootTopstitching FabNcs Check Your Needle To Change Your Needle = To Remove the Bobbin from the Machine = Wind the Bobbin PutOnto Pin With Thread Winding Direction Insertthe Bobbin into the Bobbin Hotder Thread Your Needle Pick Up Your Bobbin Thread Toward Inches Adjust the Top Thread Tension Top Indicator panel Top tension Too Tight Too LooseIs set Is up Stremh Stitch = Three Needle Position WidthPosition Needle position Three Needle Position Sem Check Chart II1 IIIOn p Refer to 52 ~ 3N6 Stitch Shell On p.15 Onp Stitch Refer to On p 155 ZoneCheck Turn a Square Corner Use the Darning Plate Use the darning plate in the following waysControl 0 grog Thread tension Center Out Control orangeControl 2 to Plate and replace foot holder and foot When you finish darning, remove the darningHeresHow Basle Zigzag Set the Machine Contro I to Contro 3 to Applique = Bar TackingVery short Pressure dial2 Embroidery Zigzag foot Darning plate Sew a Button=dth control = Rick-Rack Stretch Stitch length Control Three-Step Zigzag Stitch width control 5 to Overcast Stretch Stitching Sarging or Pine Leaf Stretch StitchinSat the Machine Zi£rzegfoot Weight Set the Machine Stitch width Control Light Ilili!!ii!iiilji = Learningto Sew Buttonholes HaveCuffs Or where Stitch wdth Control 3 to31controt Controt 2 toPage Buttonhole foot Pins a Lever Buttonhole Marked buttonhole End ol opemng Openthezipper Cosethe zipper and turn Control 3 to 8Stitch Iength control orange zone Set the Machine Stitch widthLingerie Smocking Control 3 to 6 2 Zigzag foot Stlchwidth control 3 to Zigzag toot Iii¸!iiiiii¸...........i Positron Stitch width control 3 toStitch length controt Contro green Satin stitch Whatto do when Improper IncorrectInsert Vacuum Cover plate by Driver Parts List B868 102403202813404013 655t Overedge foot 13, 27, 40, 42 Parts list 6566 Performance Plug connector Portable1920 Buttonhole Making 4551 Opener Template 6566 Two-point Box Zipper Application 5253 Foot T2, 26 6566 Settingupyourmachine Stitch SelectorPage Practical Stitch Chart FAGOT,NG Warranty Year Visit Sewing Machine385