STATUS INDICATORS

When the following indicators light up or blink on the operation panel or the following alphanumeric codes appear in the display, solve the problem immediately referring to both the table below and the relevant page.

Be sure to use only genuine SHARP parts and supplies.

 

Indication

 

Cause and remedy

Page

 

 

Steadily

Replacement of drum cartridge will be needed

70

 

Drum replacement

lit

soon. Prepare a new cartridge.

 

 

 

required indicator

Blinking

Drum cartridge must be replaced. Replace it with

58

 

 

a new one.

 

TD cartridge

Steadily

Replacement of TD cartridge will be needed

70

 

lit

soon. Prepare a new cartridge.

 

replacement

 

 

 

TD cartridge must be replaced. Replace it with a

 

 

required indicator

Blinking

57

 

new one.

 

 

 

 

 

A misfeed has occurred. Remove the misfed

 

 

Misfeed indicator

Blinking

paper referring to the description of "MISFEED

63

 

 

 

REMOVAL".

 

 

 

 

An original misfeed has occurred in the SPF/

 

 

SPF/RSPF misfeed

Blinking

RSPF. Remove the misfed originals referring to

66

 

indicator

 

the description of "E: Misfeed in the SPF (AL-

 

 

 

 

1553), RSPF (AL1555)".

 

 

 

 

The unit is in the preheat mode. Press any key to

54

 

 

 

cancel the preheat mode.

 

Power save indicator is

 

 

The unit is in the auto power shut-off mode.

 

 

steadily lit.

 

 

 

 

Press the start ( ) key to cancel the auto power

54

 

 

 

 

 

 

shut-off mode.

 

 

The paper tray indicator is

The paper tray is not installed properly. Push the

 

blinking.

 

tray into the unit securely.

 

 

 

 

 

 

 

 

 

 

 

The TD cartridge is not installed. Check if the

 

 

"CH" is blinking in the display.

cartridge is installed. If "CH" is blinking even if a

57

 

cartridge is installed properly, contact your

 

 

 

authorised service representative.

 

 

"CH" is steadily lit in the

Side cover is open. Close the side cover securely

 

 

by pressing the round projections near the side

 

display.

 

 

 

cover open button.

 

 

 

 

 

 

 

 

 

 

 

 

 

The paper tray or multi-bypass tray is empty.

15, 17

 

 

 

Load paper.

 

 

 

 

 

"P" is blinking in the display.

A misfeed has occurred in the paper tray, single

 

 

 

 

bypass or multi-bypass tray. Remove the misfed

63

 

 

 

paper.

 

 

A letter and a number appear

The scan head locking switch is locked. Unlock

 

 

the scan head locking switch and turn the power

9

 

alternately.

 

switch off/on.

 

 

 

 

 

 

 

 

 

 

 

 

 

The unit will not function. Turn the power switch

 

 

A letter and a number appear

off and then switch it on, and if there is again an

 

alternately.

 

error, remove the power cord from the outlet, and

 

 

 

 

 

 

contact your authorized service representative.

 

 

 

 

 

 

62

Page 64
Image 64
Sharp AL-1553, AL-1555, AL-1552 operation manual Status Indicators, Indication Cause and remedy