Sharp HT-SL72 operation manual ill

I ofMakethe sureTV. (HTto-SL77)enable the HDMI CEC when making HDMI

Plug the AC power cord into a AC outlet, the stand-by indicator turns RED.

The Amplifier will automatically power on if:

DIGITAL (HDMI) function: TV or similar component which supports HDMI CEC, is turned on. (HT-SL77 only) ANALOG function: Audio signal is detected from Audio input.

The Amplifier stand-by indicator will turn BLUE if TV signal is detected.

Notes:

•Make sure to select function (refer Input Selector) for a preferred connection.

•A slight audio delay after TV is turned ON does not mean that the system is faulty. This is normal.

•"AQUOS speaker is enabled" message will be displayed if SHARP LCD TV does not detect HT-SL77 during power on. However the message "AQUOS audio with AQUOS LINK is enabled" will be displayed soon as

HT-SL77 is detected. These messages may vary for other TV model.

The Amplifier and Subwoofer will link automatically (wirelessly) when turned on as it is already pre-linked at the factory. If the link cannot be established, please set the connection by the following method.

1.Press and hold the PAIRING button on the Amplifier for more than 3 seconds.

2.Within 2 minutes, press and hold the PAIRING button on the Subwoofer for more than 3 seconds

•During pairing process, the Amplifier and Subwoofer indicator will blink in BLUE for a few seconds.

•The Amplifier and Subwoofer will be linked (connected) if both unit indicators turn BLUE.

Subwoofer

Note:

Power/Pairing indicators status.

Power/Pairing	Condition
Indicator	Amplifier	Subwoofer
Turns BLUE	Power On	Power On
	(linked)	(linked)

]

connection. For details, refer to the operation manual 1I Notes:

•If a device such as microwave oven, wireless LAN card, Bluetooth device or any other device that uses the same 2.4GHz frequency near the system, some sound interruption may be heard due to interference.

•The transmission distance of the wireless signal between the Subwoofer and Amplifier is about 32 feet (10m), but may vary depending on your operating environment. If a steel-concrete or metallic wall is between the Subwoofer and the Amplifier, the system may not operate at all, because the wireless signal cannot penetrate metal.

Caution:

•Keep the Subwoofer away from water and moisture.

•To get the optimum listening performance, make sure the area around the Sound Bar and Subwoofer is clear

of any obstacles.

Turn the INPUT switch on the Amplifier to select the function mode.

DIGITAL: Select when using Digital (HDMI) connection.

ANALOG: Select when using Analog (Audio In) connection.

The Audio Return Channel (ARC) enables an HDMI ARC- capable TV to send the audio stream to the HDMI OUT terminal of the receiver. To use this function, your TV must support the ARC. Make sure the TV Audio output setting is set to PCM, not other formats such as Dolby Digital, DTS, etc. For details, refer to the operation manual of the TV.

DIGITAL (HDMI) function: Volume can only be controlled from your TV via HDMI CEC. (HT-SL77 only)

ANALOG function: Turn GAIN (AUDIO IN) knob toward MAX./MIN. to increase or decrease the volume.

This unit will automatically go to stand-by mode (both unit indicators turns RED) if:

DIGITAL (HDMI) function: TV or similar component which supports HDMI CEC, is turned off. (HT-SL77 only)

ANALOG function: No signal from Audio input is detected after 20 minutes.

Blinks	in BLUE	Pairing in	Pairing in
quickly		progress	progress
Turns	RED	Stand-by	Stand-by

This switch enables you to control the Subwoofer bass

output.

Turn the "BASS LEVEU' switch at the back of the Subwoofer to HIGH or LOW to adjust the output level.

•.....ill