Manuals / Sharp / Computer Equipment / Copier

Sharp MX-2700G, MX-2300G manual Saddle Stitch Finisher Maintenance, Open the front cover

Models: MX-2700G MX-2300G

1 67

Page 47

SADDLE STITCH FINISHER MAINTENANCE

When the staple cartridge runs out of staples, a message will appear in the operation panel. Follow the procedure below to replace the staple cartridge.

Replacing the staple cartridge

Open the front cover.

Pull out the stapler section.

Pull out until the stapler section until it stops.

3	Roller rotating knob A

Staple unit

Turn roller rotating knob A in the direction of the arrow to move the staple unit out to the front.

Turn the roller rotating knob as shown until the triangle mark is aligned with the indicator.

Remove the empty staple case.

Remove the empty staple cartridge.

Press the lock button to release the staple case cover and then remove the staple cartridge.

When staples remain, the staple cartridge cannot be removed.

Page 47

Image 47

Sharp MX-2700G, MX-2300G manual Saddle Stitch Finisher Maintenance, Open the front cover, Pull out the stapler section

Contents

Users Guide MODEL MX-2300G MX-2700G MX-2300N MX-2700NUSER AUTHENTICATION TABLE OF CONTENTS1 BEFORE USING THE MACHINE 5 MAINTENANCEPrinted manuals ABOUT THIS MANUALMANUALS PROVIDED WITH THE MACHINE Please noteManual name Icons used in the manualsOperation manuals in PDF format ContentsTURNING THE POWER ON AND OFF page REPLACING THE TONER CARTRIDGES page 1 BEFORE USING THE MACHINEPART NAMES AND FUNCTIONS EXTERIORTRAY SETTINGS FOR TRAYS 1 TO 4 page TRAY SETTINGS FOR TRAYS 1 TO 4 pageTRAY SETTINGS FOR TRAYS 1 TO 4 page TRAY SETTINGS FOR TRAYS 1 TO 4 pageCLEANING THE LASER UNIT page REPLACING THE WASTE TONER BOX page INTERIORTURNING THE POWER ON AND OFF page Fusing unit pressure adjusting levers pageAUTOMATIC DOCUMENT FEEDER AND DOCUMENT COVER Automatic document feederDocument cover REGULAR MAINTENANCE pageCONNECTORS PRINT/SEND STATUS JOB STATUS page OPERATION PANELUSER AUTHENTICATION page TOUCH PANEL pageTURNING THE POWER ON AND OFF page 14 POWER SAVE key / indicatorPOWER SAVE KEY page 15 POWER keyExample Using the touch panelTOUCH PANEL ExamplePRINT/SEND STATUS JOB STATUS When using the fax or Internet fax functions TURNING THE POWER ON AND OFFTurning on the power Turning off the powerENERGY SAVE FUNCTIONS POWER SAVE KEYPreheat Mode Auto power shut-off mode Sleep modewith the numeric keys USER AUTHENTICATIONAUTHENTICATION BY USER NUMBER Enter your user number 5 to 8 digitsLOGOUT If an incorrect user number is entered 3 times in a rowSelect your user name AUTHENTICATION BY LOGIN NAME / PASSWORDTouch the Login Name key or the key Touch the OK key Touch the Password keyIf you are logging in using a user selection key When logging in using the Direct Entry keySystem Settings Administrator User Registration If an incorrect login name or password is entered 3 times in a rowTray numbers 2 LOADING PAPERIMPORTANT POINTS ABOUT PAPER NAMES AND LOCATIONS OF TRAYSPlain paper that can be used in tray 1 to tray THE MEANING OF R IN PAPER SIZESUSEABLE PAPER More information on plain paper and special paperPaper that is not recommended Paper that cannot be usedFan the paper TRAY SETTINGS FOR TRAYS 1 TOLOADING PAPER Pull out the paper trayInsert the paper into the tray CHANGING THE PAPER SIZEPull out the paper tray Fan the paperSYSTEM SETTINGS Set the paper size and paper typeFan the paper LOADING PAPER IN TRAY 5 Large capacity trayPull out tray Place the paper in the centre of the paper tableWhen you change the type of paper loaded in tray 5, change the paper type setting in Paper Tray Settings in the system settings. See the System Settings Guide to change the paper type setting Set the bypass tray guides to the width of the paper LOADING PAPER IN THE BYPASS TRAYOpen the bypass tray Set the paper size Open the paper settings screenTouch the paper type key of the bypass tray Select the type of paper used in the bypass traySelect the bypass tray IMPORTANT POINTS WHEN USING THE BYPASS TRAYInserting paper Inserting tab paperInserting postcards and envelopes Important points when inserting postcards and envelopesImportant points when using envelopes Inserting transparency filmFusing unit pressure adjusting levers Pull out the right side coverClose the right side cover Make sure an original does not remain 3 ORIGINALSPLACING THE ORIGINAL PLACING ORIGINALS IN THE AUTOMATIC DOCUMENT FEEDERWhen the originals are the same width Adjust the original guides to the size of the originalsMixed size originals placing different sizes of originals together Place the originaloriginals printed with thermal transfer ink ribbon should not be fed Place the original PLACING THE ORIGINAL ON THE DOCUMENT GLASSOpen the automatic document feeder Close the automatic document feederGently close the automatic document Placing a thick bookPush up the far side of the automatic document feederProduct number 4 PERIPHERAL DEVICESPERIPHERAL DEVICES Product namePrinter expansion kit Product nameProduct number DescriptionSUPPLIES FINISHERPART NAMES Lower the staple case release lever and remove the staple case FINISHER MAINTENANCEReplacing the staple cartridge Open the coverClose the cover Removing staple jamsReplace the staple case Slide the finisher back to the rightSlide the finisher back to the right Lower the lever at the front end of the staple caseLower the staple case release lever and remove the staple case Replace the staple caseOpen the cover Discarding punch waste when a punch module is installedGently push the box back in Close the cover 1 Stapler compiler SADDLE STITCH FINISHERPART NAMES SUPPLIESRemove the empty staple case SADDLE STITCH FINISHER MAINTENANCEOpen the front cover Pull out the stapler sectionClose the front cover Insert a new staple cartridge into the staple casePull the seal that holds the staples straight out Push the stapler section back inBlue Roller rotating knob B Remove any paper from the stapler compilerRemoving staple jams Open the front coverRaise the lever at the front end of the Remove the misfed paperClose the saddle stitch section cover Remove the staple casePush the stapler section back in Return the lever to its original positionPush the saddle stitch finisher back and latch it to the machine Replace the staple casePush the saddle stitch finisher back and latch it to the machine Pull out the punch waste box and discard the punch wasteReturn the punch waste box to its original position Discarding punch waste when a punch module is installedScanning area 5 MAINTENANCEREGULAR MAINTENANCE Document glassPush the waste toner box into the machine CLEANING THE MAIN CHARGER OF THE PHOTOCONDUCTIVE DRUMCLEANING THE BYPASS FEED ROLLER CLEANING THE ORIGINAL FEED ROLLERRelease the waste toner box CLEANING THE LASER UNITOpen the front cover Take out the cleaning tool for the laser unit Identifying lines coloured lines caused by a dirty laser unitRemove the dirty cleaner from the tip of the cleaning tool Make sure that the cleaner at the tip ofthe cleaning tool is not dirty Pull the replacement cleaner out of the waste toner boxPush the waste toner box into the machine Clean the laser unitRepeat step 8 to clean all holes in the laser unit 4 holes Close the front cover Replace the cleaning tool1 Point the cleaner down and hook the end of the tool the end without the cleaner onto the holder on the right Locations of colour toner cartridges REPLACING THE TONER CARTRIDGESPull the toner cartridge toward you Open the front coverClose the front cover Remove the protective material from the new toner cartridgeInsert the new toner cartridge horizontally Push the cartridge in until it locks securely in placeStore toner cartridges out of the reach of small children Place the box on a flat surface REPLACING THE WASTE TONER BOXOpen the front cover Release the used waste toner box Remove the waste toner boxPush the waste toner box into the machine Install the new waste toner boxRemove the seals around the holes Plug the holesStore waste toner box out of the reach of small children Close the front coverDescription 6 ENTERING TEXTFUNCTIONS OF THE MAIN KEYS CHANGING THE ENTRY MODE pageCharacters key CHANGING THE ENTRY MODEENTERING TEXT FROM AN EXTERNAL KEYBOARD Symbols keyMX2700-EX-USR-Z1 Users GuideMODEL MX-2300G MX-2700G MX-2300N MX-2700N