Sharp MX-3610N Saddle Finisher, Punch module for finisher, Punch module for saddle finisher

SPECIFICATIONS

Saddle Finisher

Name	Finisher (MX-FN10)
Paper sizes	Depends on feeder specifications
Useable paper	Paper weight	55 g/m2 (15 lbs.) to 256 g/m2 (68 lbs.)
No. of trays	1
	Non-stapled	A3 wide (12" × 18") / A3 (11" × 17") /
		B4	(8-1/2" × 14") / A5R (5-1/2" × 8-1/2"R): 500 sheets
		A4	(8-1/2" × 11") / A4R (8-1/2" × 11"R) / B5
		B5R (7-1/4" × 10-1/2"R): 1,000 sheets
Tray capacity (80g/m2 (21 lbs.))	Staple function	A3	(11" × 17") / B4 (8-1/2" × 14"): 50 units or 500 sheets
		A4	(8-1/2" × 11") / A4R (8-1/2" × 11"R) / B5 / B5R :
		50 units or 1,000 sheets
	 Offset output is not available for A3 wide (12" × 18") /
	A5R (5-1/2" × 8-1/2"R).
Required power supply	Supplied from this machine

Weight	Approx. 40 kg (88 lbs.)
	When output paper tray is stored
	497 mm (W) × 631 mm (D) × 988 mm (H)
Dimensions	(19-9/16" (W) × 24-27/32" (D) × 38-57/64" (H))
	When output paper tray is extended
	656 mm (W) × 631 mm (D) × 988 mm (H)
	(25-53/64" (W) × 24-27/32" (D) × 38-57/64" (H))
Max. no. of stapled sheets	Max. no. of 50 sheets (A4 (8-1/2" × 11"), A4R (8-1/2" × 11"R), B5, B5R)
	Max. no. of 25 sheets (A3 (11" × 17"), B4 (8-1/2" × 14"))
Staple position	1 bottom, 1 top, 2 middle
Staple method (for saddle stitch)	Centred fold with stapling in 2 centre places
Saddle stitch fold position	Centred fold
Saddle usable sizes	A3 (11" × 17") / B4 (8-1/2 × 14") / A4R (8-1/2" × 11"R)
Saddle usable paper weight	60 g/m2 (16 lbs.) to 209 g/m2 (56 lbs.)

Punch module (for finisher)

Name	Punch module for finisher
	MX-PN11A, MX-PN11B, MX-PN11C, MX-PN11D
Paper size for punch module	A3 (11" × 17") to A4 (7-1/4" × 10-1/2"R)
	MX-PN11A 2 holes
Holes	MX-PN11B 3 holes
	MX-PN11C 4 holes
	MX-PN11D 4 holes (wide)

Punch module (for saddle finisher)

Name	Punch module for saddle finisher
	MX-PNX5A, MX-PNX5B, MX-PNX5C, MX-PNX5D
Paper size for punch module	A3 (11" × 17") to A4 (7-1/4" × 10-1/2"R)
	MX-PNX5A 2 holes
Holes	MX-PNX5B 3 holes
	MX-PNX5C 4 holes
	MX-PNX5D 4 holes (wide)

20

Required power supply	Supplied from finisher
Dimensions	98 mm (W) × 477 mm (D) × 137 mm (H)
	(3-55/64" (W) × 18-50/64" (D) × 5-26/64" (H))
Weight	Approx. 3 kg (7 lbs.)

Required power supply	Supplied from saddle finisher
Dimensions	122 mm (W) × 604 mm (D) × 248 mm (H)
	(4-27/32" (W) × 24-5/32" (D) × 9-59/64" (H))
Weight	Approx. 3.5 kg (7.7 lbs.)

Installation notes

CAUTION

Do not install the machine on an unstable or slanted surface. Install the machine on a surface that can withstand the weight of the machine.

Risk of injury due to the machine falling or toppling.

If peripheral devices are to be installed, do not install on an uneven floor, slanted surface, or otherwise unstable surface. Danger of slippage, falling, and toppling. Install the product on a flat, stable surface that can withstand the weight of the product.

Do not install in a location with moisture or dust.

Risk of fire and electrical shock.

If dust enters the machine, dirty output and machine failure may result.

Locations that are excessively hot, cold, humid, or dry (near heaters, humidifiers, air conditioners, etc.)

The paper will become damp and condensation may form inside the machine, causing misfeeds and dirty output. SPECIFICATIONS (page 18)

If the location has an ultrasonic humidifier, use pure water for humidifiers in the humidifier. If tap water is used, minerals and other impurities will be emitted, causing impurities to collect on the inside of the machine and create dirty output.

When the machine is installed, the adjusters (5) must be lowered to the floor to secure the machine (prevent it from moving).

Rotate the adjusters in the locking direction until they are in firm contact with the floor.

If you find it necessary to reposition the machine due to	Lock	Release
rearrangement of your office layout or other reason, retract the
adjusters from the floor, turn off the power, and then move the
machine.

(After moving the machine, lower the adjusters again to secure the machine.)

Locations exposed to direct sunlight

Plastic parts may become deformed and dirty output may result.

Locations with ammonia gas

Installing the machine next to a diazo copy machine may cause dirty output.

Do not install the machine in a location with poor air circulation.

A small amount of ozone is created inside the machine during printing. The amount of ozone created is not sufficient to be harmful; however, an unpleasant odor may be noticed during large copy runs, and thus the machine should be installed in a room with a ventilation fan or windows that provide sufficient air circulation. (The odor may occasionally cause headaches.)

* Install the machine so that people are not directly exposed to exhaust from the machine. If installed near a window, ensure that the machine is not exposed to direct sunlight.

Near a wall

Be sure to allow the required space around the machine for		30 cm
servicing and proper ventilation. (The machine should be no
closer than the distances indicated below from walls. The
indicated distances are for the case when a saddle finisher and	30 cm	45 cm
large capacity paper tray are not installed.)

Locations subject to vibration.

Vibration may cause failure.

CAUTION

The machine includes a built-in hard drive. Do not subject the machine to shock or vibration. In particular, never move the machine while the power is on.

•The machine should be installed near an accessible power outlet for easy connection.

•Connect the machine to a power outlet which is not used for other electric appliances. If a lighting fixture is connected to the same outlet, the light may flicker.

9