Adjusting each channel level |
| Adjust the level of the selected channel | |||||||||||
12 as desired. |
|
|
|
|
| ||||||||
Select the desired channel. |
|
|
|
|
|
|
| ||||||
11 |
|
| 1 | 2 | 3 |
| ADJUST |
|
| 7 | 08 | 9 | |
|
|
|
|
|
|
|
|
|
| 1 | 2 | 3 | |
|
|
|
|
|
|
|
|
|
| 4 | 5 | 6 | |
CHANNEL |
|
| 4 | 5 | 6 |
|
|
| CH. LEVEL |
|
|
| |
|
| 7 | 8 | 9 |
|
|
|
|
|
|
| ||
SELECTOR |
| CH. SEL | 0 |
|
|
|
|
|
|
|
| ||
|
|
|
|
| or |
|
|
|
|
| |||
| or |
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
| The LFE level can be adjusted within the range of | |||||||
Each time this button is pressed, the corresponding | |||||||||||||
channel is selected and displayed for 3 seconds as | of |
|
|
|
|
| |||||||
follows; |
|
|
|
|
| In general, we recommend the LFE level to be | |||||||
Front Left Center Front Right Rear Right | adjusted to 0 dB. (However, the recommend LFE | ||||||||||||
(Dolby Digital or DTS L(FE) | )SubWoofer |
| Rear Left | level for some early DTS software is | |||||||||
( ): Adjustable only when the digital signals from Dolby Digital or | recommended levels seems too high, lower the | ||||||||||||
DTS program source that includes LFE signal are input in the | setting as necessary. |
|
|
|
|
| |||||||
available surround mode. |
|
|
|
| If the channel display disappears, start from the | ||||||||
When it is in the stereo or Dolby Virtual mode, or | |||||||||||||
above step 11 again. |
|
|
|
|
| ||||||||
the speaker setting is “N”, center, rear or subwoofer |
|
|
|
|
| ||||||||
|
|
|
|
|
|
| |||||||
channel will not be selected. |
|
|
|
| Repeat the above steps 11 and 12 to | ||||||||
|
|
|
|
|
|
| |||||||
|
|
|
|
|
| 13 adjust other channel levels. |
|
|
| ||||
Adjusting each channel level with | 15 | At each channel, adjust the level as desired | |||||||||||
test tone |
|
|
|
|
| until the sound level of each speaker is | |||||||
Only when it is in available surround modes except | heard to be equally loud. |
|
|
| |||||||||
the Dolby Virtual and stereo modes, the volume |
|
|
|
|
|
|
| ||||||
level of each channel can be adjusted easily with the |
|
|
| 7 | 8 | 9 |
| ||||||
|
|
|
|
|
|
|
|
| 1 | 2 | 3 |
| |
|
|
|
|
|
|
|
|
| 4 | 5 | 6 |
| |
test tone function. |
|
|
|
|
| ADJUST | CH. LEVEL | 0 |
|
| |||
|
|
|
|
|
|
|
|
|
| ||||
Note: When the 6 CH DIRECT is selected as an input |
| or |
|
|
|
|
| ||||||
source, the test tone function does not work. |
|
|
|
|
|
| |||||||
|
|
|
|
|
|
| |||||||
Enter the test tone mode. |
|
|
|
|
|
|
|
|
| ||||
14 | 41 | 52 | 63 |
|
| You can select the desired channel and adjust its | |||||||
T.TONE | 0 | 9 |
|
| level with repeating the steps 11 and 12 in |
|
| ||||||
| 7 | 8 |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
| “Adjusting each channel level” procedure. |
| ||||||
|
|
|
|
|
| 16 | Cancel the test tone function. |
|
|
| |||
The test tone will be heard from the speaker of each |
|
|
|
|
|
| |||||||
|
|
|
|
|
|
| |||||||
channel for 2 seconds as follows; |
|
|
|
|
|
|
|
|
| ||||
Front Left | Center |
| Front Right |
| 1 | 2 | 3 |
|
|
| |||
|
| 7 | 8 | 9 |
|
|
| ||||||
|
|
|
|
|
|
| 4 | 5 | 6 |
|
|
| |
SUBwoofer | Rear Left | Rear Right |
| T.TONE | 0 |
|
|
|
| ||||
|
|
|
|
|
|
| |||||||
When the speaker setting is “N”, the test tone of the corresponding channel is not available.
When the selected decoding mode is not matched to the input signal format, the test tone function cannot work.
ENGLISH
17
