Shindaiwa 72362-93115, 35701 Specifications, Troubleshooting, Tools Included, Additional Problems

Specifications

Model 357

Troubleshooting

ADDITIONAL PROBLEMS

DESCRIPTION

Engine Type		2 cycle air cooled gas engine
Displacement		35.5 cc (2.17 cu.in.)
Fuel	Gasoline-Oil MixtureÑ50:1 with Shindaiwa 2-cycle Mixing Oil
Carburetor		Diaphragm (WALBRO Model WT)
Ignition		All transistor electronic ignition system
Spark Plug		Champion CJ6Y
.................................................................		For EMC compliance use NGK BPMR7A
Starting		Auto-rewind
Stopping		Grounding (toggle switch)
Power transmission		Automatic centrifugal clutch
Chain lubrication	........................................................	Automatic clutch-driven oiler
Chain		3/8" pitch, gauge 0.050"
Chain oil	Shindaiwa brand premium Bar and Chain Oil (or equivalent)
Fuel tank capacity		265 ml (9.0 oz)
Oil tank capacity		210 ml (7.1 oz)
Front/Rear Handles		Special anti-vibration mountings
Cooling system		Forced air
Safety devices	Front guard, throttle lock, chain catcher and inertial brake
Weight (less bar and chain)		4.2 kg (9.3 lbs)

Symptom

Poor acceleration.

Engine stops abruptly.

Possible Cause

Clogged air cleaner.

Clogged fuel filter.

Chain brake engaged

Carburetor mixture too rich or too lean.

Idle speed set too low.

Spark arrester clogged

Switch turned off.

Fuel tank empty.

Clogged fuel filter.

Water in the fuel.

Shorted spark plug or loose terminal.

Ignition failure.

Remedy

Clean the air cleaner element.

Replace the fuel filter.

Inspect and/or test brake. Consult with an authorized servicing dealer.

Adjust carburetor.

Adjust: 2,600-3,000 RPM (min-1)

Clean spark arrester. (See page 29).

Set the switch to ÒIÓ (ON), re-start.

Refuel.

Clean or replace filter as required.

Drain; replace with clean fuel.

Clean and replace spark plug. Tighten the terminal.

Consult with an authorized servicing dealer.

Tools Included

■Screwdriver

■Spark plug/13 mm socket wrench

■4 mm hex wrench

■5 mm hex wrench

WARNING!

Do not make unauthorized modifi- cations to this saw, guide bar, or chain!

Engine difficult to shut off.

Piston seizure.

Ground (stop) wire is disconnected, or switch is defective.

Overheating due to incorrect spark plug.

Consult with an authorized servicing dealer.

Test and replace as required.

Correct plug:

Champion CJ6Y. For EMC compliance use NGK BPMR 7A

RECOMMENDED BAR AND CHAIN COMBINATIONS

Overheated engine.

Idle engine until cool.

	Part Number
Size	Chain	Bar
12-inch	Oregon® 91 VG-45X	36120-12
14-inch	Oregon® 91 VG-53X	36349-14
16-inch	Oregon® 91 VG-57X	36450-16

WARNING!

Replacement chain for this saw must meet applicable ANSI B175.1-2000 kickback performance requirements, and/or be designated as Òlow kickback chainÓ per ANSI B175.1-2000 standards.

Chain rotates at idle speed.

Excessive vibration.

Engine idle too high.

Broken clutch spring or shoe.

Worn or damaged sprocket, chain or bar.

Bent crankshaft.

Set idle: 2,600-3,000 RPM (min-1).

Replace spring/shoes as required.

Inspect and replace chain components as required.

Consult with an authorized servicing dealer.

TROUBLESHOOTING

6

35