Installing Lite | Siemens S7-300 specs

Installing STEP 7 Lite

Note

If the CD does not start up automatically, you can start the setup program by double- clicking the Setup.exe file in the main directory of the CD.

Installing STEP 7 Lite

In order to create the control program for the drive motor on your PC, you must install the STEP 7 Lite software. The latest version of STEP 7 Lite including ser- vice pack can be found on the Internet at:

http://support.automation.siemens.com/WW/view/en/24372175

• Open the installation file and follow the instructions.

Installing the driver for the PC Adapter USB

Use the PC Adapter USB to establish the connection between the CPU 312C and the PC. The PC Adapter USB connects the USB interface of the PC with the MPI interface of the CPU 312C, thus enabling communication. In order to use the PC Adapter USB, you must install the necessary driver.

• Insert the Driver CD for the PC Adaptor USB and follow the instructions.

9

SIMATIC S7-300 Getting Started for First Time Users Getting Started, 04/2007, 6ZB5310-0NC02-0BA0

Image 13

Siemens S7-300 manual Installing Lite, Installing the driver for the PC Adapter USB

Contents

SIMATIC S7-300 Getting Started for First Time Users 04/2007Order No. 6ZB5310-0NC02-0BA0 Danger Safety GuidelinesQualified Personnel Trademarks Prescribed UsageDisclaimer of Liability Page 7 Congratulations Contents 1 Welcome To accomplish this, you will perform the following tasks Validity 1 WelcomePrerequisites You will need a micro Order number Materials and toolsQuantity Siemens You can also use the In addition, you will need the following componentsVDE 0805 / EN 60950 / IEC 950 or VDE 0106 Part Page 2 Preparing the PC Installing the driver for the PC Adapter USB Installing STEP 7 LiteOpen the installation file and follow the instructions 1. Open the dialog for setting the PG/PC interface Setting the interface2 Preparing the PC Page 2 Preparing the PC Page 3 Installing and wiring the hardware 3.1 What components are required? 3 Installing and wiring the hardware 3.2 Installing the componentsInstalling and grounding the mounting rail 2. Connect the mounting rail to the ground wire 1. Install the power supply, tighten Installing modules on the mounting rail2. Install the CPU 312C ing the screws hand-tight Preparing the cables 3.3 Wiring the components1. Cut the cables to the desired 2. Remove the insulation and press 1. Prepare the power cable Wiring the CPU 312C and the power supply2. Connect the power cable to the power supply 3. Secure the power cable 1. Connect the momentary contact switches to the digital inputs Wiring the momentary contact switches 1. Connect the power supply for the digital inputs Wiring the motor 2. Wire the motor, if available. This step is optional Connecting the front panel connector 2. If necessary, change the switch position for the line voltage Checking the line voltage setting 3.4 Commissioning the hardware Connecting the CPU 312C and the PC1. Connect the USB cable to the PC Adapter and your PC 2. Close the front panel 1. Connect the supply cable to the supply system Supplying power to the CPU 312C 3 Installing and wiring the hardware 3. Set the main switch of the power supply to “ON” Testing the connections Page 4 Configuring the control in STEP 7 Lite 4.1 What is a STEP 7 Lite project? 4.2 Opening a STEP 7 Lite project 4 Configuring the control in STEP 7 LiteOpening the “conveyor” project 1. Start STEP 7 Lite Creating the module configuration 4.3 Reproducing the module configuration in STEP 7 Lite1. Create a new S7-300 station 4 Configuring the control in STEP 7 Lite Page 4 Configuring the control in STEP 7 Lite 1. Set the amount of retentive bit memory to “0” Setting the parameters of the CPU 312C 1. Save the project Saving the project Establishing the online connection 4.4 Establishing the online connection between the PC and CPU 312C Performing a memory reset on the CPU 312C 4.5 Downloading and checking the module configuration to the CPU 312C1. Delete the old program blocks and configurations from the CPU 312C Downloading the module configuration to the CPU 312C Checking the module configuration Page 5 Opening the program on the PC 5.1 What is a program? 5 Opening the program on the PC 5.2 Opening a program1. Open the program Page 6 Performing a test run 6.1 Downloading the project to the CPU 312C 6.2 Starting the test run 1. Set the mode switch of the CPU 312C to “RUN”6 Performing a test run 2. Press the green momentary con- tact switch to start the motor The output LED 0.5 lights up. The input LED 0.3 lights up The motor is switched offThe output LED 0.3 goes out Page 7 Congratulations Want to know more about SIMATIC S7-300? Contact us 8 Additional information 8.1 Diagnostics / correction of errors 8 Additional information 8.2 Additional documentation Description Name of manual 8.3 SIMATIC Technical Support Service & Support on the InternetPage 8 Additional information