SIMATIC Technical Support, Additional information | Siemens S7-300

8.3 SIMATIC Technical Support

8Additional information

8.3 SIMATIC Technical Support

How to contact Technical Support for all A&D products

•By e-mail: adsupport@siemens.com

•By phone: +49 (0) 180 5050 222

•By fax: +49 (0) 180 5050 223

You can find additional information about our technical support on the Internet at

http://www.siemens.com/automation/service

Service & Support on the Internet

In addition to our documentation, we offer a comprehensive online knowledge base on the Internet at:

http://www.siemens.de/automation/csi_en_WW/product There you will find:

•The latest product information, FAQs, and downloads.

•Our newsletter, providing you with the latest information about your products.

•A Knowledge Manager to find the right documents for you.

•Our bulletin board, where users and specialists share their knowledge world- wide.

•Your local contact for Automation & Drives in our Contacts Database (see Contacts & Partners).

•You will find information on local service, repairs, spares and much more under “Services”.

62

SIMATIC S7-300 Getting Started for First Time Users Getting Started, 04/2007, 6ZB5310-0NC02-0BA0

Image 66

Siemens S7-300 manual SIMATIC Technical Support, Service & Support on the Internet, Additional information

Contents

04/2007 SIMATIC S7-300 Getting Started for First Time UsersOrder No. 6ZB5310-0NC02-0BA0 Safety Guidelines DangerQualified Personnel Prescribed Usage TrademarksDisclaimer of Liability Page Contents 7 Congratulations 1 Welcome To accomplish this, you will perform the following tasks Prerequisites 1 WelcomeValidity You will need a micro Quantity Materials and toolsOrder number Siemens In addition, you will need the following components You can also use theVDE 0805 / EN 60950 / IEC 950 or VDE 0106 Part Page 2 Preparing the PC Installing STEP 7 Lite Installing the driver for the PC Adapter USBOpen the installation file and follow the instructions Setting the interface 1. Open the dialog for setting the PG/PC interface2 Preparing the PC Page 2 Preparing the PC Page 3 Installing and wiring the hardware 3.1 What components are required? Installing and grounding the mounting rail 3.2 Installing the components3 Installing and wiring the hardware 2. Connect the mounting rail to the ground wire 2. Install the CPU 312C Installing modules on the mounting rail1. Install the power supply, tighten ing the screws hand-tight 1. Cut the cables to the desired 3.3 Wiring the componentsPreparing the cables 2. Remove the insulation and press 2. Connect the power cable to the power supply Wiring the CPU 312C and the power supply1. Prepare the power cable 3. Secure the power cable Wiring the momentary contact switches 1. Connect the momentary contact switches to the digital inputs Wiring the motor 1. Connect the power supply for the digital inputs 2. Wire the motor, if available. This step is optional Connecting the front panel connector Checking the line voltage setting 2. If necessary, change the switch position for the line voltage Connecting the CPU 312C and the PC 3.4 Commissioning the hardware1. Connect the USB cable to the PC Adapter and your PC 2. Close the front panel Supplying power to the CPU 312C 1. Connect the supply cable to the supply system 3 Installing and wiring the hardware 3. Set the main switch of the power supply to “ON” Testing the connections Page 4 Configuring the control in STEP 7 Lite 4.1 What is a STEP 7 Lite project? Opening the “conveyor” project 4 Configuring the control in STEP 7 Lite4.2 Opening a STEP 7 Lite project 1. Start STEP 7 Lite 4.3 Reproducing the module configuration in STEP 7 Lite Creating the module configuration1. Create a new S7-300 station 4 Configuring the control in STEP 7 Lite Page 4 Configuring the control in STEP 7 Lite Setting the parameters of the CPU 312C 1. Set the amount of retentive bit memory to “0” Saving the project 1. Save the project 4.4 Establishing the online connection between the PC and CPU 312C Establishing the online connection 4.5 Downloading and checking the module configuration to the CPU 312C Performing a memory reset on the CPU 312C1. Delete the old program blocks and configurations from the CPU 312C Downloading the module configuration to the CPU 312C Checking the module configuration Page 5 Opening the program on the PC 5.1 What is a program? 5.2 Opening a program 5 Opening the program on the PC1. Open the program Page 6 Performing a test run 6.1 Downloading the project to the CPU 312C 1. Set the mode switch of the CPU 312C to “RUN” 6.2 Starting the test run6 Performing a test run 2. Press the green momentary con- tact switch to start the motor The motor is switched off The output LED 0.5 lights up. The input LED 0.3 lights upThe output LED 0.3 goes out Page 7 Congratulations Want to know more about SIMATIC S7-300? Contact us 8 Additional information 8.1 Diagnostics / correction of errors 8.2 Additional documentation 8 Additional information Name of manual Description Service & Support on the Internet 8.3 SIMATIC Technical SupportPage 8 Additional information