Wiring the momentary contact switches | Siemens S7-300 guide

Wiring the momentary contact switches

3Installing and wiring the hardware

Wiring the momentary contact switches

1. Connect the momentary contact switches to the digital inputs.













/

1


/
/
0
0
	/
	/
0	0

20

SIMATIC S7-300 Getting Started for First Time Users Getting Started, 04/2007, 6ZB5310-0NC02-0BA0

Image 24

Siemens S7-300 manual Wiring the momentary contact switches, Connect the momentary contact switches to the digital inputs

Contents

04/2007 SIMATIC S7-300 Getting Started for First Time UsersOrder No. 6ZB5310-0NC02-0BA0 Safety Guidelines DangerQualified Personnel Prescribed Usage TrademarksDisclaimer of Liability Page Contents 7 Congratulations 1 Welcome To accomplish this, you will perform the following tasks 1 Welcome ValidityPrerequisites You will need a micro Materials and tools Order numberQuantity Siemens In addition, you will need the following components You can also use theVDE 0805 / EN 60950 / IEC 950 or VDE 0106 Part Page 2 Preparing the PC Installing STEP 7 Lite Installing the driver for the PC Adapter USBOpen the installation file and follow the instructions Setting the interface 1. Open the dialog for setting the PG/PC interface2 Preparing the PC Page 2 Preparing the PC Page 3 Installing and wiring the hardware 3.1 What components are required? 3.2 Installing the components 3 Installing and wiring the hardwareInstalling and grounding the mounting rail 2. Connect the mounting rail to the ground wire Installing modules on the mounting rail 1. Install the power supply, tighten2. Install the CPU 312C ing the screws hand-tight 3.3 Wiring the components Preparing the cables1. Cut the cables to the desired 2. Remove the insulation and press Wiring the CPU 312C and the power supply 1. Prepare the power cable2. Connect the power cable to the power supply 3. Secure the power cable Wiring the momentary contact switches 1. Connect the momentary contact switches to the digital inputs Wiring the motor 1. Connect the power supply for the digital inputs 2. Wire the motor, if available. This step is optional Connecting the front panel connector Checking the line voltage setting 2. If necessary, change the switch position for the line voltage Connecting the CPU 312C and the PC 3.4 Commissioning the hardware1. Connect the USB cable to the PC Adapter and your PC 2. Close the front panel Supplying power to the CPU 312C 1. Connect the supply cable to the supply system 3 Installing and wiring the hardware 3. Set the main switch of the power supply to “ON” Testing the connections Page 4 Configuring the control in STEP 7 Lite 4.1 What is a STEP 7 Lite project? 4 Configuring the control in STEP 7 Lite 4.2 Opening a STEP 7 Lite projectOpening the “conveyor” project 1. Start STEP 7 Lite 4.3 Reproducing the module configuration in STEP 7 Lite Creating the module configuration1. Create a new S7-300 station 4 Configuring the control in STEP 7 Lite Page 4 Configuring the control in STEP 7 Lite Setting the parameters of the CPU 312C 1. Set the amount of retentive bit memory to “0” Saving the project 1. Save the project 4.4 Establishing the online connection between the PC and CPU 312C Establishing the online connection 4.5 Downloading and checking the module configuration to the CPU 312C Performing a memory reset on the CPU 312C1. Delete the old program blocks and configurations from the CPU 312C Downloading the module configuration to the CPU 312C Checking the module configuration Page 5 Opening the program on the PC 5.1 What is a program? 5.2 Opening a program 5 Opening the program on the PC1. Open the program Page 6 Performing a test run 6.1 Downloading the project to the CPU 312C 1. Set the mode switch of the CPU 312C to “RUN” 6.2 Starting the test run6 Performing a test run 2. Press the green momentary con- tact switch to start the motor The motor is switched off The output LED 0.5 lights up. The input LED 0.3 lights upThe output LED 0.3 goes out Page 7 Congratulations Want to know more about SIMATIC S7-300? Contact us 8 Additional information 8.1 Diagnostics / correction of errors 8.2 Additional documentation 8 Additional information Name of manual Description Service & Support on the Internet 8.3 SIMATIC Technical SupportPage 8 Additional information