![](/images/new-backgrounds/1248556/2485569x1.webp)
<<CHART A>>
Camera | Lens Type | Exp. Mode | Metering | TTL System | Note | Conf | |
|
|
|
|
|
| Dist | |
F5 | D, G Type | All Modes | All Modes |
|
| ||
F100 | BL | Can switch to TTL Mode. With | 1 | ||||
|
|
| |||||
F90X/N90ser. | AF lens other than | All Modes | All Modes | F5, F100, F80, series Cameras |
| ||
F80/N80ser. | D, G type | spot metering system is always |
| ||||
F70D/N70 | Without Built in CPU | A/M | Center Weighted / | TTL. | 2 | ||
F75/N75 | Modes | Spot Metering | Spot | Can switch to TTL Mode. TTL BL | |||
F4 Series | With | All Modes | Matrix Pattern | TTL BL | 1 | ||
Center Weighted / | can work with only F4 series, AF | ||||||
|
| Spot Metering | Spot | F3, |
| ||
|
|
| Center | metering system of F4 is always |
| ||
F65/N65 | Without | A/M | TTL. Pronea 600i will be TTL, | 2 | |||
Weighted/Spot | |||||||
Pronea 600i | Modes | Spot Metering | when exposure mode is “M”. |
| |||
|
|
|
| Center Weighted BL cannot work. |
| ||
|
|
|
|
|
| ||
| With | All Modes | Matrix Pattern | TTL BL |
|
| |
F601/N6006 | Center Weighted / | Spot Metering cannot use with | 2 | ||||
|
| Spot Metering | Spot | ||||
|
|
|
|
| |||
Without | A/M | Center Weighted / |
| ||||
| Modes | Spot Metering | Spot | If exposure mode is “M”, it will be |
| ||
F60D/N60 | With | P/S |
| TTL BL | 2 | ||
F50D/N50 |
| A/M |
|
| Center Weighted/Spot |
| |
Without |
|
| Center Weighted / |
| 2 | ||
M |
|
| |||||
| Spot |
| |||||
| P |
| TTL Programmed |
|
| ||
F501/N2020 | A/M |
| TTL |
| 2 | ||
AF F3 Lens |
|
| |||||
F301/N2000 |
|
|
|
| |||
Except above | A/M |
| TTL |
|
| ||
|
|
|
| ||||
| lenses |
|
|
| |||
|
|
|
|
|
| ||
F401S/N4004S | With | P/S |
| TTL Programmed |
| 2 | |
A/M |
| TTL |
| ||||
F401/N4004 |
|
|
|
| |||
Without | M |
| TTL |
| 2 | ||
|
|
| |||||
FA, FE2 | With | A/M |
| TTL |
| 2 | |
FG, F3, FM3 | Without |
|
|
Confirm Distance:
1 : Flash’s LCD panel will show the
2 : Set the
◆When using Digital SLR cameras, functions will vary depending on the lens type and combinations of exposure modes, same as F5 and F100 group (in chart A), however, they will use
LIMITS OF CONTINUOUS SHOOTING
To prevent overheating of the flash’s circuitry, do not use your Flash unit for at least 10minutes after continiously using the flash as shown in the table below.
Mode | Number of Flash Exposures |
TTL, M(1/1,1/2) | 15 Continuous Flash Shots |
M(1/4, 1/8) | 20 Continuous Flash Shots |
40 Continuous Flash Shots | |
Multi | 10 Cycle |
MANUAL FLASH OPERATION
Manual flash is provided for shooting subjects when the correct exposure is difficult to obtain in the TTL mode. In the manual flash mode, you can set the flash power level from 1/1 to 1/64 power in 1/3 stop increments.
1.Set the camera’s exposure mode (A, M modes).
2.Press the MODE button on the flash unit to select M.
3.Press the SEL button to make the guide number value blink.
4.Press + or – button to set the desired flash power output.
5.To stop the manual flash output display blinking, Press the SEL button again.
6.When the Ready Light of the flash is illuminated, the unit is ready for use.
17