![](/images/new-backgrounds/1258623/25862371x1.webp)
Mounting The
Table Saw
Mounting Table Saw to Workbench
If table saw is to be used in a permanent location, it should be fastened securely to a firm supporting surface such as a stand or workbench, using the four mounting holes, 1 two of which are shown (Fig. 25).
When mounting table saw to a workbench or plywood, holes should be drilled through the supporting surface of the workbench or plywood and a opening MUST be made the same size as the opening in the bottom of the saw using the dimensions illustrated (Fig. 26), so the saw dust can drop through.
FIG. 25
|
|
|
|
|
|
| º |
|
|
|
|
|
| 4 | 5 |
|
|
|
|
| º |
|
|
|
|
|
|
| 40 |
|
|
|
|
|
|
| º |
|
|
|
|
|
|
| 35 |
|
|
|
|
|
|
| º |
|
|
|
|
|
|
| 0 |
|
|
|
|
|
|
| 3 |
|
|
|
|
|
|
| º |
|
|
|
|
|
| 5 |
|
| |
|
|
| º | 2 |
|
|
|
|
| 0º 15º | 20 |
|
|
|
|
| º |
|
|
|
|
| |
0º | 5 |
|
|
|
|
|
|
1
1
1.Each of the four mounting holes should be bolted securely using 5/16" hex nuts (not included). Screw lengths should be
2.Locate and mark where the saw is to be mounted.
3.Drill four (4) 3/8" diameter holes through workbench.
4.Place table saw on workbench aligning holes in base with holes drilled in workbench.
5.Insert four (4) 5/16" screws and tighten.
Mounting to Plywood
An alternative method of securing your table saw is to fasten the saw base to a mounting board 24" x 24" minimum size to prevent saw from tipping while in use. Any good grade of plywood with a 3/4" minimum thickness is recommended.
FIG. 26
24” 16”
24” |
3/8" Dia. |
16” |
1.Follow instructions for mounting to workbench, substituting a plywood board 24" x 24" minimum size and using 5/16" flat head machine screws, flat washers, and hex nuts (not included). Screw length must be at least
NOTE: For proper stability, holes must be counter sunk on bottom side of plywood so screw heads are flush with the bottom surface of the supporting board.
2.Securely clamp board 2 to workbench 3 using two or more “C” clamps, 4 as shown (Fig. 27).
Supporting surface where saw is to be mounted should be examined carefully after mounting to insure that no movement can occur during use. If any tipping or walking is noted, secure the workbench or stand before operating the table saw.
NOTE: All dimensions in inches.
REMARQUE : Toutes les dimensions sont en pouces.
NOTA: Todas las dimensiones están en pulgadas.
FIG. 27
|
|
|
|
|
| º |
|
|
|
|
| º | 45 |
|
|
|
|
|
| |
|
|
|
|
| 40 |
|
|
|
|
|
| º |
|
|
|
|
|
| 35 |
|
|
|
|
|
| º |
|
|
|
|
|
| 30 |
|
|
|
|
|
| º |
|
|
|
|
| º | 25 |
|
|
|
|
|
|
| |
|
|
| 15º | 20 |
|
|
| 5º | 10º |
|
|
| |
0º |
|
|
|
| ||
|
|
|
|
|
2
3
4
4
36.