SkyLink LS-318 manual Countdown Timer Operating Mode, Erasing Transmitters From The Module, Fcc

7. COUNTDOWN TIMER OPERATING MODE

If a Countdown Timer Mode transmitter or sensor is activated, the light connected to the Screw-In Dimmer will be on for the predetermined time Interval. During the timer count down, the red LED on the Screw-In Dimmer will be on steadily. Activating a programmed transmitter or sensor under Regular Mode or Flashing Alert Mode during timer interval can override the countdown timer operation.

8. ERASING TRANSMITTERS FROM THE MODULE

You may erase a transmitter or sensor from the Screw-In Dimmer, but you cannot erase a specific device directly, you must erase all the wireless devices, then program the ones you want to keep. Follow the instructions below to erase programmed transmitters / sensors.

Method 1 (Required the use of a programmed transmitter / sensor):

1.Power off the Screw-In Dimmer by switching off the wall switch.

2.Transmit a "Erase" code from the transmitter until step 4.

3.Power up the Screw-In Dimmer by switching on the wall switch.

4.You may stop the "Erase" code signal transmission. You have now successfully erased all the transmitters / sensors.

Method 2 (Does not require the use of any transmitter / sensor)

1.Turn off the light and Screw-In Dimmer by the wall switch.

2.Place the operating mode slide switch to the “Timer” position.

3.Press and hold the SET button. Do not release the SET button until step 5.

4.While holding on the SET button, turn on the light and Screw-In Dimmer by the wall switch. The red LED flashes quickly. You may need another person helping you to do this.

CAUTION

DO NOT TOUCH ANY METAL PARTS WHILE PRESSING THE SET BUTTON. MAKING CONTACT WITH INNER METAL PARTS MAY RESULT IN ELECTRICAL SHOCK CAUSING SEVERE OR FATAL INJURY.

5.You may release the SET button, now you have successfully erased all the devices.

9. TECHNICAL SPECIFICATIONS

Input Voltage: 120V AC, 60Hz

Standby Current: 6mA

Minimum Load: 10W

Maximum Rating: 2 Amps

Maximum Load: 200W at 120VAC

Operating Frequency: 318MHz

Operational Temperature: -4° F - 140° F (-20° C - 60° C)

Humidity: 5%-95%

Range: Up to 500 feet in open area

CUSTOMER SERVICE

17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3 Email:support@skylinkhome.com http://www.skylinkhome.com

P/N. 101Z708

Patent Pending

©2010 SKYLINK GROUP

10. FCC

The Remote Control is approved by the FCC and it complies with Part 15 of the FCC Rules. Its operation is subject to the following two conditions :

1.This device may not cause harmful interference.

2.This device must accept any interference that may cause undesired operation.

WARNING:

Changes or modifications to this unit not expressly approved by the party responsible of compliance could void the user’s authority to operate the equipment.

11. WARRANTY

If, within one year from date of purchase, this product should become defective (except battery), due to faulty workmanship or materials, it will be repaired or replaced, without charge. Proof of purchase and a Return Authorization are required.

12. CUSTOMER SERVICE

If you would like to

-find out the up-to-date specifications

-know more about features and applications

-download documents, i.e. user’s instructions

-order Skylink products

or if you have difficulty getting products to work, please:

1.visit our FAQ section at www.skylinkhome.com, or

2.email us at support@skylinkhome.com, or

3.call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST. Fax (800) 286-1320

13. ACCESSORIES

The SkylinkHomeTM System consists of many other devices such as SkylinkHomeTM Remotes, Motion Sensor, ON/OFF Wall Switch, Wall Dimmer, Plug-In Dimmer with or without Repeater, Plug-In ON/OFF Control (Outdoor/Indoor), Screw-In Dimmer, ON/OFF/Dimming Control, ON/OFF Control, Smart ButtonTM Garage Door Control, etc. Please visit Skylink website at www.skylinkhome.com for more information.