BATTERY MAINTENANCE

MOTION SENSOR BATTERY

The Motion Sensor operates on a 9 volt alkaline battery accessible beneath a sliding panel on the bottom of the unit. All remote sensors come with the battery. Disarm the Control Panel before replacing all batteries.

When low battery level is detected, the motion sensor will beep to alert you the battery needs to be replaced. When the low battery signal appears, it will not trans- mit any signal to the receiver even motion is detected. Therefore, you should replace the battery as soon as the low battery signal appears.

Note: Alkaline battery must be used.

To replace the Motion Sensor battery:

1.Slide to remove the sensor from the ball-head joint.

2.Undo the screw and remove the battery cover.

3.Take the old battery out of the battery compartment.

4.Disconnect the old battery from the connector wire.

5.Connect the new alkaline battery to the connector wire.

6.Put the new battery into the battery compartment.

7.Close the battery cover and re-insert the screw.

8.Slide the unit back to the ball-head joint.

BATTERY MAINTENANCE

DOOR/WINDOW SENSOR BATTERY

Each door/window sensor operates on a 12 volt alkaline battery that is inside the transmitter. The sensors come with the batteries already installed.

To replace the battery:

1.

Push on the clip at the bottom of the transmitter

 

 

case with a sharp object (such as a paper clip

 

 

or pen knife) and pull it away from the backplate.

-

2.

Pry out the old battery from one end.

3.

Push the new battery back into place. A diagram

+

 

beside the battery well indicates which end is

 

 

positive and which is negative.

 

4.Snap the transmitter back onto the backplate.

KEYCHAIN TRANSMITTER BATTERY

The Keychain Transmitter operates on a 12 volt alkaline battery which is installed at the factory.

There are two screws on the back of the transmitter that holds the case together.

To replace the Keychain Transmitter battery:

1.Undo the two screws on the back of the transmitter.

The back will then come off.

2.Using a small screwdriver or pen knife, pry out the old battery from one end.

3.Place the new battery in position.

A diagram beside the battery well

+

indicates which end is positive and

which is negative.

-

 

4.Close the battery cover and re-insert the two screws.

–25–

–26–

Page 14 Page 16
Page 15
Image 15
SkyLink SC-100 manual Motion Sensor Battery, DOOR/WINDOW Sensor Battery, Keychain Transmitter Battery
Page 14 Page 16

SC-100 specifications

The SkyLink SC-100 is an advanced drone designed for a variety of aerial applications, catering to both professionals and enthusiasts. This versatile drone integrates cutting-edge technology, making it stand out in a competitive market.

One of the key features of the SkyLink SC-100 is its high-resolution camera, capable of capturing stunning 4K videos and high-quality images. The camera is equipped with a gimbal stabilization system that eliminates vibrations, ensuring smooth footage even in challenging conditions. This is particularly beneficial for photography, videography, and surveillance tasks, allowing users to capture detailed imagery from a bird's-eye view.

The drone boasts an impressive flight time of up to 30 minutes on a single charge, thanks to its efficient battery design. This extended duration allows users to conduct longer missions without the need for frequent recharges. The SC-100 also features an intelligent battery management system that monitors the battery's health and performance, providing users with data to ensure optimal operation.

Speed and agility are hallmarks of the SkyLink SC-100, which can reach speeds of up to 50 km/h. Its powerful motors and aerodynamic design enable it to perform complex maneuvers with ease, making it suitable for dynamic applications such as racing or search and rescue missions. Additionally, the drone is equipped with a range of smart flight modes, including follow-me, waypoint navigation, and orbit mode, enhancing its adaptability for various scenarios.

Another noteworthy feature is its robust obstacle avoidance system. The SC-100 incorporates multiple sensors, including ultrasonic and visual sensors, allowing it to perceive its surroundings and navigate safely without collisions. This technology is particularly useful for beginners and professionals alike, providing an added layer of safety during flight.

Furthermore, the SkyLink SC-100 supports a user-friendly mobile app that enables real-time control and monitoring. The app provides access to advanced features such as live streaming of footage, customizable flight paths, and detailed telemetry data. Users can easily share their captured content through integrated social media options, enhancing engagement with their audience.

In summary, the SkyLink SC-100 stands out with its high-quality camera, impressive flight time, speed, obstacle avoidance technology, and user-friendly controls. These features make it an exceptional choice for drone enthusiasts and industry professionals looking to leverage aerial technology for various applications. Whether for recreational use, aerial photography, or commercial projects, the SC-100 promises reliability and performance.
Top Page Image Contents