Glossary-1, 1000BASE-T, Auto-Negotiation | SMC Networks specification

GLOSSARY

10BASE-T

IEEE 802.3 specification for 10 Mbps Ethernet over two pairs of Category 3, 4, or 5 UTP cable..

100BASE-TX

IEEE 802.3u specification for 100 Mbps Fast Ethernet over two pairs of Category 5 UTP cable.

1000BASE-T

IEEE 802.3ab specification for Gigabit Ethernet over two pairs of Category 5, 5e 100-ohm UTP cable.

Auto-Negotiation

Signalling method allowing each node to select its optimum operational mode (e.g., 10 Mbps or 100 Mbps and half or full duplex) based on the capabilities of the node to which it is connected.

Bandwidth

The difference between the highest and lowest frequencies available for network signals. Also synonymous with wire speed, the actual speed of the data transmission along the cable.

Glossary-1

Image 57

SMC Networks manual Glossary-1, 1000BASE-T, Auto-Negotiation, Bandwidth

Contents

TigerSwitch Page TigerSwitch Installation Guide Trademarks Limited Warranty Limited Warranty FCC Class a CompliancesIndustry Canada Class a Japan Vcci Class a EC Conformance Declaration Class a Iii Taiwan Bsmi Class a Australia AS/NZS 3548 1995 Class a Safety Compliance Warnhinweis Faseroptikanschlüsse Optische SicherheitUnderwriters Laboratories Compliance Statement Wichtige Sicherheitshinweise Germany Compliances Table of Contents Specifications C-1 Troubleshooting A-1Making Network Connections Cables B-1 Ordering Information D-1 Glossary Index Index-1 Table of Contents Overview Chapter About Tigerswitch Description of Hardware 1000BASE-T PortsGbic Slots Port and System LEDs Status LEDs Network Management Agent VLANs Spanning Tree Protocol Power Supply Receptacles Optional Redundant Power UnitMulticast Switching Traffic Priority Features and Benefits ConnectivityPerformance Management Chapter Network Planning Introduction to Switching Backbone Consolidation Sample Applications Making Vlan Connections Making Vlan Connections Mbps Gigabit Ethernet Collision Domain Connectivity RulesMaximum Fiber Optic Cable Distance for 1000BASE-SX Maximum Fiber Optic Cable Distance for 1000BASE-LX Mbps Fast Ethernet Collision Domain Maximum 100BASE-TX Network Diameter Using RepeatersSMC 3-2 Rule for Class II Repeaters SMC 2-1 Rule for Class I Repeaters Mbps Ethernet Collision Domain Application NotesSMC 5-4-3 Rule Maximum Cable Length Selecting a Site Installing the Switch Equipment Checklist Package ContentsOptional Rack-Mounting Equipment Rack Mounting Mounting Attaching the Brackets Attaching the Adhesive Feet Desktop or Shelf Mounting Installing a Gbic Transceiver Power Receptacle Connecting to a Power Source Installing the Switch Chapter Making Network Connections Connecting Network Devices Connecting to 1000BASE-T Devices Connecting to an SC-Type Fiber Port Maximum 1000BASE-LX Gigabit Ethernet Cable Length Appendix a Troubleshooting Diagnosing Switch IndicatorsPower and Cooling Problems In-Band Access Installation Appendix B Cables Specifications 1000BASE-T Pin Assignments Twisted-Pair Cable and Pin Assignments Pin MDI Signal Name MDI-X Signal Name Cable Testing for Existing Category 5 Cable Adjusting Existing Category 5 Cabling1000BASE-T Cable Requirements DB-9 Port Pin Assignments Console Port Pin Assignments Console Port to 25-Pin DTE Port on PC Console Port to 9-Pin COM Port on PC Physical Characteristics Appendix C Specifications Switch Features Standards Management Features Safety WarrantyCompliances Emissions Appendix D Ordering Information Ordering Information Glossary-1 Glossary1000BASE-T Auto-Negotiation Glossary-2 Glossary-3 Glossary-4 Glossary-5 Glossary-6 Virtual LAN Vlan Glossary-7 Glossary-8 Index-1 Index Index-2 Index-3 Index-4 Page For Technical SUPPORT, Call