Appendix B Cables | SMC Networks SMC8748ML3, SMC8724ML3 specification

APPENDIX B

CABLES

Twisted-Pair Cable and Pin Assignments

For 10BASE-T/100BASE-TX connections, a twisted-pair cable must have two pairs of wires. For 1000BASE-T connections the twisted-pair cable must have four pairs of wires. Each wire pair is identified by two different colors. For example, one wire might be green and the other, green with white stripes. Also, an RJ-45 connector must be attached to both ends of the cable.

Caution: Each wire pair must be attached to the RJ-45 connectors in a specific orientation.

Caution: DO NOT plug a phone jack connector into any RJ-45 port. Use only twisted-pair cables with RJ-45 connectors that conform with FCC standards.

Figure B-1 illustrates how the pins on the RJ-45 connector are numbered. Be sure to hold the connectors in the same orientation when attaching the wires to the pins.

8

8

11

Figure B-1 RJ-45 Connector Pin Numbers

B-1

Image 67

SMC Networks SMC8748ML3, SMC8724ML3 manual Appendix B Cables, Twisted-Pair Cable and Pin Assignments

Contents

TigerStack Page TigerStack Installation Guide Trademarks Limited Warranty SMC Networks, Inc Tesla Irvine, CA Japan Vcci Class a CompliancesFCC Class a Industry Canada Class a CE Mark Declaration of Conformance for EMI and Safety EEC Warnhinweis Faseroptikanschlüsse Optische Sicherheit Safety CompliancePower Cord Safety Australia AS/NZS 3548 1995 Class a Power Cord Set France et Pérou uniquement Vii Schuko Viii Environmental Statement Audience PurposeRelated Publications Table of Contents Xii Making Network Connections Xiii Appendices Xiv Tables Figures Figures Xvi Overview Chapter About Tigerstack Front Panels Switch Architecture Network Management Options Description of Hardware10/100/1000BASE-T Ports Stacking Ports SFP Slots Port LEDs Port Status LEDs Port and System Status LEDs System Status LEDs Power Supply Sockets Optional Redundant Power Unit Module LEDs Optional Media Extender ModulesExtender Module LEDs 10G Xenpak Module Performance Features and BenefitsConnectivity Expandability Management Chapter Network Planning Introduction to Switching Collapsed Backbone Application Examples Network Aggregation Plan Network Aggregation Plan Remote Connections with Fiber Cable Remote Connections with Fiber Cable Making Vlan Connections Making Vlan Connections IP Routing for Unicast Traffic Using Layer 3 Routing Application Notes Network Planning Selecting a Site Installing the Switch RJ-45 Connections Ethernet Cabling Package Contents Equipment ChecklistOptional Rack-Mounting Equipment Rack Mounting Mounting Attaching the Brackets Rack-Montage Montage Rack Mounting German Attaching the Adhesive Feet Desktop or Shelf Mounting Installing an Optional Module Installing an Optional Module into the Switch Inserting an SFP Transceiver into a Slot Installing an Optional SFP Transceiver into the Switch Connecting Switches in a Stack Making Stacking Connections Stacking Topologies Power Socket Connecting to a Power Source Wiring Map for Serial Cable Connecting to the Console PortWiring Map for Serial Cable Cabling Guidelines Connecting Network DevicesChapter Making Network Connections Twisted-Pair Devices Making Twisted-Pair Connections Connecting to PCs, Servers, Hubs and Switches Wiring Closet Connections Network Wiring Connections Fiber Optic SFP Devices Making Connections to SFP Transceivers Gbps Fiber Optic Connections Connecting to Xenpak Transceiver Maximum 10GBASE-SR 10 Gigabit Ethernet Cable Length Connectivity Rules1000BASE-T Cable Requirements Gbps Ethernet Collision Domain Mbps Gigabit Ethernet Collision Domain Maximum Fast Ethernet Cable Length Mbps Fast Ethernet Collision DomainMbps Ethernet Collision Domain Maximum 1000BASE-ZX Fiber Optic Cable Length Cable Labeling and Connection Records Diagnosing Switch Indicators Appendix a TroubleshootingTable A-1 Troubleshooting Chart Table A-2 Power/RPU LEDs Diagnosing Power Problems with the LEDs Installation Power and Cooling ProblemsIn-Band Access Stack Troubleshooting Twisted-Pair Cable and Pin Assignments Appendix B Cables Table B-1 10/100BASE-TX MDI and MDI-X Port Pinouts 10BASE-T/100BASE-TX Pin Assignments Figure B-2 Straight-through Wiring Straight-Through Wiring Figure B-3 Crossover Wiring Crossover Wiring 1000BASE-T Pin Assignments Cable Testing for Existing Category 5 CableTable B-2 1000BASE-T MDI and MDI-X Port Pinouts Fiber Standards Adjusting Existing Category 5 Cabling to Run 1000BASE-T Physical Characteristics Appendix C Specifications Power Supply Switching DatabaseWeight Temperature Management Features Switch Features CE Mark Emissions SafetyStandards Compliances Extender Modules Warranty10G Extender Module Xenpak Specifications Appendix D Ordering Information Table D-1 TigerStack 1000 Products and Accessories Ordering Information Glossary-1 Glossary1000BASE-T Glossary-2 Glossary-3 Glossary-4 Glossary-5 Glossary-6 Index-1 Index Index-2 Index-3 Index-4 Page For Technical SUPPORT, Call