SMC Networks SMC8724ML3, SMC8748ML3 specs

COMPLIANCES

CE Mark Declaration of Conformance for EMI and Safety (EEC)

SMC contact for these products in Europe is:

SMC Networks Europe, Edificio Conata II,

Calle Fructuós Gelabert 6-8, 2o, 4a,

08970 - Sant Joan Despí, Barcelona, Spain.

This information technology equipment complies with the requirements of the Council Directive 89/336/EEC on the Approximation of the laws of the Member States relating to Electromagnetic Compatibility and 73/23/EEC for electrical equipment used within certain voltage limits and the Amendment Directive 93/68/EEC. For the evaluation of the compliance with these Directives, the following standards were applied:

RFI Emission:	• Limit class A according to EN 55022:1998
	• Limit class A for harmonic current emission according to
	EN 61000-3-2/1995
	• Limitation of voltage fluctuation and flicker in low-voltage supply
	system according to EN 61000-3-3/1995
Immunity:	• Product family standard according to EN 55024:1998
	• Electrostatic Discharge according to EN 61000-4-2:1995
	(Contact Discharge: ±4 kV, Air Discharge: ±8 kV)
	• Radio-frequency electromagnetic field according to EN 61000-4-3:1996
	(80 - 1000 MHz with 1 kHz AM 80% Modulation: 3 V/m)
	• Electrical fast transient/burst according to EN 61000-4-4:1995 (AC/
	DC power supply: ±1 kV, Data/Signal lines: ±0.5 kV)
	• Surge immunity test according to EN 61000-4-5:1995
	(AC/DC Line to Line: ±1 kV, AC/DC Line to Earth: ±2 kV)
	• Immunity to conducted disturbances, Induced by radio-frequency
	fields: EN 61000-4-6:1996 (0.15 - 80 MHz with
	1 kHz AM 80% Modulation: 3 V/m)
	• Power frequency magnetic field immunity test according to
	EN 61000-4-8:1993 (1 A/m at frequency 50 Hz)
	• Voltage dips, short interruptions and voltage variations immunity test
	according to EN 61000-4-11:1994 (>95% Reduction @10 ms, 30%
	Reduction @500 ms, >95% Reduction @5000 ms)
LVD:	• EN60950:2000

Warning: Do not plug a phone jack connector in the RJ-45 port. This may damage this device.

Attention: Les raccordeurs ne sont pas utilisés pour le système téléphonique!

iv

Image 8

SMC Networks SMC8724ML3, SMC8748ML3 manual CE Mark Declaration of Conformance for EMI and Safety EEC

Contents

TigerStack Page TigerStack Installation Guide Trademarks Limited Warranty SMC Networks, Inc Tesla Irvine, CA Compliances FCC Class aIndustry Canada Class a Japan Vcci Class a CE Mark Declaration of Conformance for EMI and Safety EEC Safety Compliance Power Cord SafetyAustralia AS/NZS 3548 1995 Class a Warnhinweis Faseroptikanschlüsse Optische Sicherheit Power Cord Set Vii France et Pérou uniquement Viii Schuko Environmental Statement Related Publications PurposeAudience Table of Contents Making Network Connections Xii Appendices Xiii Tables Xiv Figures Xvi Figures Chapter About Tigerstack Overview Switch Architecture Front Panels 10/100/1000BASE-T Ports Description of HardwareNetwork Management Options SFP Slots Stacking Ports Port and System Status LEDs Port LEDs Port Status LEDs System Status LEDs Optional Redundant Power Unit Power Supply Sockets Optional Media Extender Modules Extender Module LEDs10G Xenpak Module Module LEDs Features and Benefits ConnectivityExpandability Performance Management Introduction to Switching Chapter Network Planning Application Examples Collapsed Backbone Network Aggregation Plan Network Aggregation Plan Remote Connections with Fiber Cable Remote Connections with Fiber Cable Making Vlan Connections Making Vlan Connections Using Layer 3 Routing IP Routing for Unicast Traffic Application Notes Network Planning Installing the Switch Selecting a Site Ethernet Cabling RJ-45 Connections Optional Rack-Mounting Equipment Equipment ChecklistPackage Contents Mounting Rack Mounting Attaching the Brackets Montage Rack Mounting German Rack-Montage Desktop or Shelf Mounting Attaching the Adhesive Feet Installing an Optional Module into the Switch Installing an Optional Module Installing an Optional SFP Transceiver into the Switch Inserting an SFP Transceiver into a Slot Connecting Switches in a Stack Making Stacking Connections Stacking Topologies Connecting to a Power Source Power Socket Wiring Map for Serial Cable Connecting to the Console PortWiring Map for Serial Cable Connecting Network Devices Chapter Making Network ConnectionsTwisted-Pair Devices Cabling Guidelines Connecting to PCs, Servers, Hubs and Switches Making Twisted-Pair Connections Network Wiring Connections Wiring Closet Connections Fiber Optic SFP Devices Gbps Fiber Optic Connections Making Connections to SFP Transceivers Connecting to Xenpak Transceiver Connectivity Rules 1000BASE-T Cable RequirementsGbps Ethernet Collision Domain Maximum 10GBASE-SR 10 Gigabit Ethernet Cable Length Mbps Gigabit Ethernet Collision Domain Mbps Fast Ethernet Collision Domain Mbps Ethernet Collision DomainMaximum 1000BASE-ZX Fiber Optic Cable Length Maximum Fast Ethernet Cable Length Cable Labeling and Connection Records Table A-1 Troubleshooting Chart Appendix a TroubleshootingDiagnosing Switch Indicators Diagnosing Power Problems with the LEDs Table A-2 Power/RPU LEDs In-Band Access Power and Cooling ProblemsInstallation Stack Troubleshooting Appendix B Cables Twisted-Pair Cable and Pin Assignments 10BASE-T/100BASE-TX Pin Assignments Table B-1 10/100BASE-TX MDI and MDI-X Port Pinouts Straight-Through Wiring Figure B-2 Straight-through Wiring Crossover Wiring Figure B-3 Crossover Wiring Table B-2 1000BASE-T MDI and MDI-X Port Pinouts Cable Testing for Existing Category 5 Cable1000BASE-T Pin Assignments Adjusting Existing Category 5 Cabling to Run 1000BASE-T Fiber Standards Appendix C Specifications Physical Characteristics Switching Database WeightTemperature Power Supply Switch Features Management Features Safety StandardsCompliances CE Mark Emissions 10G Extender Module Xenpak WarrantyExtender Modules Specifications Table D-1 TigerStack 1000 Products and Accessories Appendix D Ordering Information Ordering Information 1000BASE-T GlossaryGlossary-1 Glossary-2 Glossary-3 Glossary-4 Glossary-5 Glossary-6 Index Index-1 Index-2 Index-3 Index-4 Page For Technical SUPPORT, Call