Manuals / Brands / Computer Equipment / Computer Hardware / SMSC / Computer Equipment / Computer Hardware

SMSC EMC2102 Figure 5.25 Spin-upCase 1 Fix, Figure 5.24 Theoretical Plot of Case

1 38

Download 38 pages, 4.31 Mb

Fan Speed Control with the EMC2102 Device

Fan Speed

(RPM)RPM for

100% Drive

Target Speed

Valid Speed

rpm60 or rpm75

Fan Speed

¼of Spin Up Time

Spin Up Time

Check TACH

Figure 5.24 Theoretical Plot of Case 1

Spin Up Level

Changed to 75%

Figure 5.25 Spin-up Case 1 Fix 1

If the fan is already set to 75% level, we will need to lower the valid speed (function of 56h, Valid TACH) to a value below the rpm75, to fix the problem.

To test this situation, set spin-up level to 75% (53h[2] = 1), set the Valid TACH Count (56h) = 6000 rpm and then start the fan (57h) with 6500 rpm. The spin-up routine will run repeatedly.

Change the Valid TACH Count (56h) to 5800 rpm, the problem cannot be fixed since the valid speed is still higher than the fan speed (rpm75 = 5650 rpm).

Set 56h = 5580 rpm which is below 5650 rpm (the rpm75), the system gets out of the spin-up routine (Figure 5.26).

SMSC EMC2102

USER MANUAL

Revision 0.2 (09-17-07)

Contents

USER MANUAL Page Page Page Page Page Figure 4.1 EMC2102 Fan Control Evaluation System Figure 4.2 EVB-EMC2102Board 5.1.1ChipMan Installation 5.1.2Setting Up the ChipMan Figure 5.1 ChipMan Message for First Operation Note: Figure 5.2 ChipMan Device Selection Window Figure 5.3 Selecting the Device and Master Controller Type Figure 5.4 ChipMan Operation Window Notes: Figure 5.5 Changing Fan Speed 5.1.3Plotting From ChipMan Figure 5.6 Plotting from the ChipMan Figure 5.7 Plot Windows Figure 5.8 Plot Examples 5.2.1Getting Started 5.2.2Basic RPM Based Fan Control Figure 5.9 Plots for Proper Control Settings 5.2.3Effects of Loading Figure 5.10 Effects of Loading 5.2.4Register Change Summary Table 5.1 Register Change Summary for Experiment REGISTER DEFAULT 5.3.1Fan Control Parameters Figure 5.11 Fan Control Parameters 5.3.2Getting Started 5.3.3Forced Kick Function Figure 5.12 Forced Kick Function 5.3.4Spin-UpLevel Figure 5.13 60% Spin Level Setting 5.3.5Spin-UpTime Figure 5.14 Reduced Spin-upTime 5.3.6Register Change Summary Table 5.2 Register Change Summary for Experiment 5.4.1General Setup 5.4.2Controlling the Ramp Rate Figure 5.15 Default Ramp Rate Figure 5.16 Default Step Size with Different UPDATE Settings Figure 5.17 Default UPDATE with Different Step Size Settings Figure 5.18 Exceptionally Slow Rate 5.4.3Register Change Summary Table 5.3 Register Change Summary for Experiment 5.5.1General Setup 5.5.2Fan Configuration Register (52h) Figure 5.19 Update Time Modifications 5.5.3FAN Minimum Drive Register (55h) and Valid TACH Count (56h) Figure 5.20 Minimum Drive Setting Figure 5.21 Valid Tach Count Setting 5.5.4Register Change Summary Table 5.4 Register Change Summary for Experiment 5.6.1General Setup 5.6.2Fan Spin and Stall Interrupts Figure 5.22 Fan Spin and Stall 5.6.3Register Change Summary 5.7.1.1Case 1 - Spin-upLvel RPM < Valid RPM < Target RPM Figure 5.24 Theoretical Plot of Case Figure 5.25 Spin-upCase 1 Fix 5.7.1.2Case 2 - Valid RPM << Target RPM < Spin-upLevel RPM 5.7.1.3Case 3 - Valid RPM =< Target RPM << Spin-upLevel RPM Figure 5.30 Spin-upCase Figure 5.31 Spin-upRoutine Restarted During Normal Operation 5.7.1.4Case 4 - 4.Valid RPM < Spin-upLevel RPM (rpm60 or rpm75) < Target RPM 5.7.1.5Case 5 - Correct RPM Relationships with a Slow Response DC Fan Figure 6.1 A Typical 2-poleDC Fan Figure 6.2 Output Signal of a 2-poleFan Figure 6.3 Fan TACH Measurement With EMC2102 [1] 6.2.1General Setup 6.2.2Set the Correct LIMIT2K Value 6.2.3Determine the Number of Poles and the Maximum Fan Speed 6.2.4Determine the Minimum Startup Speed 6.2.5Determine the Stall Speed 6.2.6Determine the Minimum Valid TACH Speed 6.2.8.1Spin-upLEVEL (Register 53h[2]) 6.2.8.2Minimum Fan Speed 6.2.8.3Valid TACH Count Speed (Function of Register 56h) 6.2.8.4Maximum Fan Speed