Manuals / Snapper / Lawn and Garden / Lawn Mower

Snapper 5900683, 5900709, 5900734 manual Regular Maintenance, Reinstall the mower deck guards

Models: 5900683, 5900709, 5900734

1 48

Download 48 pages 29.85 Kb

Page 35

12.Reinstall the mower deck guards.

7.Install the new chevron belt on the right-hand sprocket and make sure that the belt is properly seated in the chevron of the sprocket.

8.Refer to Figure 42. Align the holes in the sprockets with the spindle mounting hardware as shown. The blades will be perpendicular to each other.

9.Install the new chevron belt on the left-hand sprocket and make sure that the belt is properly seated in the chevron of the sprocket.

10.Carefully rotate the breaker bar CLOCKWISE and install the deck drive belt on the stationary idler pulley (D, Figure 41). Carefully release the tension on the breaker bar. When the idler arm is released it will position the stationary idler pulley and the chevron belt idler pulley (B & C, Figure 40) in the correct position.

11.Tighten the hardware that secures the stationary idler pulley and the chevron belt idler pulley to the cutter deck.

12.Reinstall the mower deck guards.

13.Run the mower under no-load condition for about 5 minutes to break-in the new belt.

Regular Maintenance

Figure 42. Blade Alignment (36” Models)

Maintenance

33

Image 35

Snapper 5900683, 5900709, 5900734 manual Regular Maintenance, Reinstall the mower deck guards, Blade Alignment 36” Models

Contents

Briggs & Stratton Yard Power Products Group OPERATOR’S MANUALS50X Series Zero-Turn Riding Mower5375 N. Main St Munnsville, NY See Features and Controls for the location of Identification NumbersContact Information Briggs & Stratton Yard Power Products Group DATE PURCHASEDFeatures & Controls Safety Controls Operation Maintenance Troubleshooting SpecificationsTable of Contents Operator SafetySafety Operator SafetyOperator Safety THROWN OBJECTS Operator SafetySafety SLOPE OPERATIONRETAINING WALLS, DROP-OFFS, AND WATER Operator SafetySafety FUEL AND MAINTENANCEPREPARATION Operator SafetySafety TRAININGDo Not Operator SafetySafety periods of exposureMaintenance and Storage Operator SafetySafety SERVICE AND MAINTENANCESafety Decals Operator SafetySafety Safety DANGERCAUTION or NOTICE Operator SafetyFigure 1. Identification Numbers A. Identification Tag Features and ControlsFeatures and Controls ControlsControls Features and ControlsSeat Adjustment Lever Ignition SwitchHour Meter / Maintenance Reminder Features & ControlsPTO Power Take Off Switch Deck Lift Pedal, Cutting Height Adjustment Pin & Deck Lift Lock LeverNever allow passengers to ride on the unit OperationOperation OperationTire Figure 5. Seat Adjustment A. Seat Adjustment LeverOperation OperationFigure 7. Foot Pedal Adjustment A. Deck Lift Foot Pedal OperationTo adjust pedal position Figure 6. Mowing Height Adjustment A. Cutting Height Adjustment PinDO NOT TOW RIDER OperationOperation 2. NOTE A warm engine may not require chokingForward Travel Practice OperationOperation Figure 9. Move Control Levers GraduallyFigure 12. Turning Around a Corner OperationOperation Executing TurnsHeight of Grass OperationOperation 8. Stop the engine see Stopping The Rider and EngineOperation When and How Often to MowNote Always operate the engine at full throttle when mowing How Much Grass to Cut Off When BroadcastingProper Mulching Figure 18. Trailer Weight Recommendations A. Clevis Pin B. ClipOperation OperationSafety Items Regular MaintenanceRegular Maintenance MaintenanceB. Cap C. Oil Filter D. Fuel Filter E. Fuel Tank Selection Valve Regular MaintenanceMaintenance Figure 19. Engine Oil Drain Briggs & Stratton shown A. Oil Drain HoseLubricating the Front Casters Regular MaintenanceMaintenance GreaseFigure 24. Checking Transmission Oil Level Regular MaintenanceMaintenance Change Interval Every 200 Hours Replacement Filter NumberDANGER Regular MaintenanceMaintenance Always wear gloves when handling mower blades or working near bladesAlways wear safety eye protection when grinding Regular MaintenanceMaintenance Always wear gloves when handling the mower bladesTo Adjust the Handle Placement Regular MaintenanceMaintenance To Adjust the Handle AlignmentB. First Measurement - .50” 1,27 cm C. Brake Spring Rod D. Lock Nut Regular MaintenanceMaintenance Figure 34. Parking Brake Adjustment A. Brake SpringFigure 35. Return-to-Neutral Adjustment A. Jam Nuts Regular MaintenanceMaintenance AdjustmentDeck Leveling Adjustment Regular MaintenanceMaintenance Deck Rod Timing AdjustmentFigure 40. Mower PTO Belt A. Idler Arm B. Stationary Idler Pulley Regular MaintenanceMaintenance To avoid damaging belts, DO NOT PRY BELTS OVER PULLEYSFigure 42. Blade Alignment 36” Models Regular MaintenanceMaintenance 12. Reinstall the mower deck guardsFigure 43. Mower PTO Belt A. Idler Arm B. Stationary Idler Pulley Regular MaintenanceMaintenance To avoid damaging belts, DO NOT PRY BELTS OVER PULLEYSUse extreme caution when removing this spring Regular MaintenanceMaintenance Hydraulic Pump Drive Belt ReplacementCleaning the Battery and Cables Regular MaintenanceMaintenance NOTE This unit is equipped with a maintenance-free BCIU1 batteryCharging a Completely Discharged Battery Regular MaintenanceMaintenance Checking Battery VoltageDischarged Regular MaintenanceMaintenance Starting After Long Term Storage Regular MaintenanceMaintenance StorageProblem TroubleshootingTroubleshooting TroubleshootingProblem TroubleshootingTroubleshooting Troubleshooting the MowerCause TroubleshootingTroubleshooting Problem19 HP Kawasaki SpecificationsSpecifications Engine Power Rating InformationLINE Ferris Industries - a division of Simplicity Manufacturing Inc Owners Limited Warranty InformationFERRIS LIMITED WARRANTY Warranty PeriodBELTS AND BLADES Product SpecificationsCommon Service Parts ENGINE