GeneralOutputs:Audio outputs terminal (front/rear) Subwoofer output terminal (mono)Power antenna (aerial) relay control terminal Power amplifier control terminalInputs:Remote controller input terminalAntenna (aerial) input terminalTelephone ATT control terminalIllumination control terminalBUS control input terminalBUS audio input terminalAUX input jack (stereo mini jack)USB signal input terminalTone controls:Low: ±10 dB at 60 Hz (XPLOD)Mid: ±10 dB at 1 kHz (XPLOD)High: ±10 dB at 10 kHz (XPLOD) Power requirements: 12 V DC car battery

(negative ground (earth)) Power supply voltage: 11 – 16 V Dimensions: Approx. 178 ⋅ 50 ⋅ 182 mm

(7 1/8 ⋅ 2 ⋅ 7 1/4 in) (w/h/d)

Mounting dimensions: Approx. 182 ⋅ 53 ⋅ 162 mm (7 1/4 ⋅ 2 1/8 ⋅ 6 1/2 in) (w/h/d)

Mass: Approx. 1.3 kg (2 lb 14 oz)Supplied accessories:Card remote commander: RM-X151Parts for installation and connections (1 set)Optional accessories/equipment:Rotary commander: RM-X4SBUS cable (supplied with an RCA pin cord): RC-61 (1 m), RC-62 (2 m)CD changer (10 discs): CDX-757MXCD changer (6 discs): CDX-T69Source selector: XA-C40AUX-IN selector: XA-300USB connection cable for iPod: RC-100IPHD RadioTM tuner: XT-100HD

Your dealer may not handle some of the above listed accessories. Please ask the dealer for detailed information.

Design and specifications are subject to change without notice.

•Halogenated flame retardants are not used in the certain printed wiring boards.

•Halogenated flame retardants are not used in cabinets.

•Packaging cushions are made from paper.

Troubleshooting

The following checklist will help you remedy problems you may encounter with your unit. Before going through the checklist below, check the connection and operating procedures.

If the problem is not solved, visit the following support site.

Support site

http://esupport.sony.com

http://www.sony.com/xplod

GeneralNo power is being supplied to the unit.•Check the connection or fuse.

•If the unit is turned off and the display disappears, it cannot be operated with the remote commander. t Turn on the unit.

The power antenna (aerial) does not extend. The power antenna (aerial) does not have a relay box.

No sound.

•The ATT function is activated, or the Telephone ATT function (when the interface cable of a car telephone is connected to the ATT lead) is activated.

•The position of the fader control “FAD” is not set for a 2-speaker system.No beep sound.•The beep sound is canceled (page 16).

•An optional power amplifier is connected and you are not using the built-in amplifier.

The contents of the memory have been erased.•The RESET button has been pressed. t Store again into the memory.

•The power supply lead or battery has been disconnected or it is not connected properly.

Stored stations and correct time are erased. The fuse has blown.Makes noise when the position of the ignition is switched.The leads are not matched correctly with the car’s accessory power connector.During playback or reception, demonstration mode starts.

If no operation is performed for 5 minutes with “DEMO-ON” set, demonstration mode starts.

tSet “DEMO-OFF” (page 16).The display disappears from/does not appear in the display window.•The dimmer is set “DIM-ON” (page 17).

•The display disappears if you press and hold (OFF). t Press and hold (OFF) on the unit until the

display appears.•The connectors are dirty (page 21).

22