The drive comes
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 39 |
|
|
| 1 |
|
|
|
|
|
|
|
| Audio |
| R | Master Pin |
|
|
|
|
|
|
| +5 G G +12 |
|
|
| ||||||||||||
|
|
|
|
| 40 |
|
|
| 2 |
|
|
|
|
| ||||||||||||||
|
|
|
|
|
| IDE ATAPI |
|
|
|
|
|
| ||||||||||||||||
| Output |
|
| Jumpered |
|
|
|
|
|
|
|
| DC Power |
|
| |||||||||||||
|
|
|
|
|
| |||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Connector |
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Slave pin | (open) |
| Pin 1 |
|
|
|
|
|
|
If the drive is the only drive on the EIDE port then the drive should be the master drive. To make the Drive the master drive you put the jumper block on the Master pin position
Cable Select
Slave
Master
If the drive will be using the same port with a hard drive, then the hard drive should be set as the master and the drive as the slave drive. To make the drive the slave drive you put the jumper block on the Slave pin position.
Slave
Master
Cable Select
7.Install the drive.
To install the drive, position the drive in the drive bay so that the screw holes of the drive are aligned with the screw holes in the drive bay. Then tighten the screws until they are firm. Do not over tighten the screws.
DIGITAL | ANALOG |
|
|
|
|
|
|
| |||
AUDIO |
| CABLE |
|
|
| ||||||
|
| AUDIO |
| SELECT |
|
| |||||
|
|
|
|
|
|
|
| ||||
0 | 0 |
|
|
|
| SLAVE |
|
| |||
R | G G |
| C |
| M | ASTER |
|
| |||
|
|
| L |
| S M |
|
|
|
|
| |
|
|
|
| S |
|
| 39 |
|
| ||
|
|
|
|
| L A |
|
| HOST | INTERFACE | ||
|
|
|
|
|
|
|
|
| 40 |
1 |
| POWER |
| |
2 | +5 | G |
|
|
| G | +12 | ||
|
| |||
|
|
|
|
20 | 21 |