Viewfinder Advanced Menu

Advanced menu page 2

Advanced menu page 3

Menus and Indications Screen Viewfinder 4 Chapter

(NEXTm$ PREVm4)

PAGE2

 

 

 

GAIN

 

 

 

mLOW

:

OdB

MID

:

9dB

HIGH

: 18dB

HYPER: 36dB

 

 

 

DL

: ON

 

(YESmPUSH)

EXIT

MENU

 

 

 

 

Item

Settings

 

 

GAIN

This sets gain values for the positions of the GAIN switch. The HIGH, MID, and LOW values must be set so that LOW < MID < HIGH.

LOW

–3 dB, 0 dB (normal

Sets the L position.

value), 3 dB, 6 dB, 9 dB,

 

12 dB, 18 dB, 18 dB + DPR,

 

24 dB

 

 

MID

0 dB, 3 dB, 6 dB, 9 dB

Sets the M position.

(normal value), 12 dB,

 

18 dB, 18 dB + DPR, 24 dB,

 

24 dB + DPR

 

 

HIGH

3 dB, 6 dB, 9 dB, 12 dB,

Sets the H position.

18 dB (normal value),

 

18 dB + DPR, 24 dB, 24 dB

 

+ DPR, HYPER GAIN

 

 

HYPER

36 dB (normal value),

Sets the HYPER position.

42 dB

 

 

DL

ON (normal value), OFF

Sets DynaLatitude function

When set to ON, the amount

ON/OFF. This setting is

of DynaLatitude effects is

valid only when the

set in the basic menu page 2

OUTPUT/DL/DCC+ switch

(see page 81). For details on

has been set to CAM/DL.

the DynaLatitude function,

 

see page 50.

 

 

 

 

 

 

 

 

PAGE3 (NEXTm$ PREVm4)

 

 

mAWB MEM

: 2

 

 

 

TONE

 

: ON

 

 

BARS

 

: SMPTE a)

 

 

REMOTE1

: REC

 

 

 

REMOTE2

: MARK

 

 

 

BAUD

RATE: 38400

 

 

 

 

 

 

 

 

 

 

 

 

EXIT MENU (YESmPUSH)

 

 

 

 

a) For DSR-500WSPL: EBU75

 

 

 

 

 

Item

Settings

 

 

 

 

 

 

AWB MEM

2 (normal value): No

Selects whether or not

correspondence with FILTER

to make the FILTER

control settings. Only two

control settings (1 to 4)

adjustment values (A and B) are

correspond to

stored in memory.

separate white

2 ⋅ 4FL: Correspondence with

balance adjustment

FILTER control settings. Each of

values stored in

the four control settings can be

memory.

used to set A and B adjustment

 

 

values, for a total of eight settings.

TONE

ON (normal value): Outputs

Selects whether or not

audio signal.

 

 

to output a 1-kHz

OFF: Does not output audio

audio signal with the

signal.

 

 

color bars when the

 

 

 

 

OUTPUT/DL/DCC+

 

 

 

 

has been set to

 

 

 

 

BARS.

 

 

 

 

BARS

SMPTE (normal value for DSR-

Selects normal width

500WSL): Normal width

or narrower width for

EBU75 (normal value for DSR-

color bars.

500WSPL): EBU 75%

 

 

EBU100 (for DSR-500WSPL):

 

 

EBU 100%

 

 

 

 

SPLIT (for DSR-500WSPL): Not

 

 

for normal operation

 

 

SNG: Narrower than normal (used

 

 

for satellite communications, etc.)

REMOTE1

REC (normal value): Specifies

Sets a function for

recording start/stop.

switch 1 of the RM-

MARK: Specifies a Mark IN/OUT

LG1 connected to the

point.

 

 

REMOTE connector 1.

CUE: Specifies a Cue point.

 

 

NG: Specifies NG/OK.

REMOTE2

REC: Specifies recording start/stop.

Sets a function for

MARK (normal value): Specifies

switch 2 of the RM-

a Mark IN/OUT point.

LG1 connected to the

CUE: Specifies a Cue point.

REMOTE connector 1.

NG: Specifies NG/OK.

 

 

 

 

BAUD RATE

9600, 38400 (normal value)

Sets a baud rate for a

 

 

 

 

computer connected

 

 

 

 

to the REMOTE

 

 

 

 

connector 2 (to be

 

 

 

 

supported in the future

 

 

 

 

version).

 

 

 

 

 

 

 

 

 

 

88 Chapter 4 Viewfinder Screen Indications and Menus