Sony HT-DDW890 Specifications

Specifications

Amplifier section

Power Output1)

Models of area code CEL, CEK

Stereo mode (6 ohms, 1 kHz, THD 1%) 90 W + 90 W

Surround mode2) (reference) (6 ohms, 1 kHz, THD 10%)

RMS output FRONT:135 W per channel CENTER:135 W SURROUND:135 W per channel

SURROUND BACK:

135W

1)Measured under the following conditions:

Area code	Power requirements
CEL, CEK	230 V AC, 50 Hz

2)Reference power output for front, center, surround and surround back speakers. Depending on the sound field settings and the source, there may be no sound output.

Inputs (Analog)

SA-CD/CD/CD-R,	Sensitivity: 800 mV
TV, SAT, DVD,	Impedance: 50 kohms
VIDEO 1, 3

Inputs (Digital)

DVD (Coaxial)	Sensitivity: –
	Impedance: 75 ohms

SAT, VIDEO 2/BD	Sensitivity: –
(Optical)	Impedance: –

Outputs (Analog)

SA-CD/CD/CD-R	Voltage: 800 mV
(OUT),	Impedance: 10 kohms
VIDEO 1 (AUDIO
OUT)

SUB WOOFER	Voltage: 2 V
	Impedance: 1 kohm

Reproduction frequency range:

	28 – 20,000 Hz
Tone

Gain levels	±6 dB, 1 dB step

FM tuner section
Tuning range	87.5 - 108.0 MHz
Antenna	FM wire antenna
Antenna terminals	75 ohms, unbalanced
Intermediate frequency
	10.7 MHz

AM tuner section

Tuning range

Models of area code CEL, CEK

With 9-kHz tuning scale:

	531 – 1,602 kHz
Antenna	Loop antenna
Intermediate frequency
	450 kHz

Video section

Inputs/Outputs

Video:	1 Vp-p, 75 ohms
COMPONENT VIDEO:
	Y: 1 Vp-p, 75 ohms
	PB/CB: 0.7 Vp-p, 75 ohms
	PR/CR: 0.7 Vp-p, 75 ohms
	80 MHz HD Pass Through

General

Power requirements

Area code	Power requirements
CEL, CEK	230 V AC, 50/60 Hz

Power output (DIGITAL MEDIA PORT)
DC OUT:	5V, 700 mA
Power consumption

Area code	Power consumption

CEL, CEK	200 W

Power consumption (during standby mode) 0.3 W

78GB

Contents

Page Page About This Manual Note for the supplied remote Table of Contents Getting Started Enjoying Surround Sound Tuner Operations Amplifier Operations Description and location of parts Receiver Front panel Page About the indicators on the display Page Rear panel Remote commander RM-AAP017 Page Page Page Page 1: Installing speakers Example of a 6.1 channel speaker system configuration Installing the speakers on a flat surface Installing the speakers on the speaker stand Installing the speakers on the wall 2: Connecting speakers To connect the speakers correctly 3a: Connecting the audio components Connecting a Super Audio CD/CD player or CD recorder 3b: Connecting the video components How to hook up your components Video input/output jack to be connected Component to be connected Connecting components with HDMI jacks If you connect a Blu-raydisc player Notes on HDMI connections Notes on digital audio signals connection Connecting a TV Connecting a DVD player/DVD recorder Connecting a DVD player Connecting a DVD recorder Connecting a satellite tuner/ set-topbox Page 4: Connecting the antennas 5:Preparing the receiver and the remote Inserting batteries into the remote 6:Selecting the speaker system To turn off the speaker output 7:Calibrating the appropriate settings automatically Error and warning codes Error codes To rectify the error Error code and remedies Warning codes To change the settings manually Warning code and solution 8:Adjusting the speaker levels and balance Selecting a component To mute the sound To avoid damaging your speakers To listen to the sub woofer Listening/Watching a component Listening to a Super Audio CD/CD Watching a DVD Navigating through menus To return to the previous display To exit the menu Overview of the menus Page Adjusting the level (LEVEL menu) LEVEL menu parameters Adjusting the tone (TONE menu) TONE menu parameters Settings for the surround sound (SUR menu) Using the surround back decoding mode Types of the surround back decoding functions Settings for the tuner (TUNER menu) TUNER menu parameters Settings for the audio (AUDIO menu) Settings for the video (VIDEO menu) VIDEO menu parameters Settings for the system (SYSTEM menu) SYSTEM menu parameters Page Enjoying Dolby Digital and DTS surround sound Types of A.F.D. mode Selecting a preprogrammed sound field Types of sound field available About DCS (Digital Cinema Sound) About CINEMA STUDIO EX modes To turn off the surround effect for movie/music Resetting sound fields to the initial settings Listening to FM/AM radio Direct tuning If you cannot tune in a station Presetting radio stations Presetting radio stations Tuning to preset stations Naming preset stations Using the Radio Data System (RDS) Displaying RDS information Description of program types Switching between digital and analog audio Enjoying the DIGITAL MEDIA PORT Connecting the DIGITAL MEDIA PORT adapter To detach the DIGITAL MEDIA PORT adapter from DMPORT jack Listening to a connected component through DMPORT connection Watching a connected component through DMPORT connection Naming inputs Changing the display All inputs except the FM and AM band FM and AM band Using the Sleep Timer Recording using the receiver Recording onto a CD-R Recording onto a recording media Programming the remote If programming is unsuccessful, check the following: To clear the memory of the remote To program the remote to control a TV To cancel programming To activate the input after programming To control a CD player To control a DAT deck To control an MD deck To control a tape deck To control an LD player To control a DVD player To control a DVD recorder To control a TV To control a satellite tuner To control a cable box To control a tuner To control a Blu-raydisc recorder To control a PSX Glossary Page Precautions On safety On power sources On heat buildup On placement Troubleshooting Audio Page Video Tuner Remote control Error messages If you are unable to remedy the problem using the troubleshooting guide If the problem persist Reference sections for clearing Specifications Page Index Numerics