Sony 4-130-033-13(1), HT-SF360 Specifications

69US

Additional Information

Specifications

AUDIO POWER

SPECIFICATIONS

POWER OUTPUT AND TOTAL

HARMONIC DISTORTION:

(Models of area code UC only)

With 3 ohm loads, both channels driven, from

170 – 20,000 Hz; rated 84 watts per channel

minimum RMS power, with no more than 1%

total harmonic distortion from 250 milliwatts

to rated output.

Amplifier section

Models of area code UC

Power Output1)

Stereo mode (rated) 84 W + 84 W

(3 ohms at 170 –

20,000 Hz, THD 1%)

Surround mode (reference)

RMS Output

(3 ohms at 1 kHz,

THD 10%)

FRONT2): 143 W/ch

CENTER2): 143 W

SUR2): 143 W/ch

(1.5 ohms at 70 Hz,

THD 10%)

SUBWOOFER2): 285 W

Models of area code MX

Power Output1)

Stereo mode (rated) 90 W + 90 W

(3 ohms at 1 kHz,

THD 1%)

Surround mode (reference)

RMS Output

(3 ohms at 1 kHz,

THD 10%)

FRONT2): 125 W/ch

CENTER2): 125 W

SUR2): 125 W/ch

(1.5 ohms at 70 Hz,

THD 10%)

SUBWOOFER2): 210 W

1)Measured under the following conditions:

2)Reference power output for front, center, surround

speakers and subwoofer. Depending on the sound

field settings and the source, there may be no

sound output.

Inputs

Analog Sensitivity: 1 V/50 kohms

Digital (Coaxial) Impedance: 75 ohms

Tone

Gain levels ±10 dB, 0.5 dB step

Reproduction frequency range:

28 – 20,000 Hz

FM tuner section

Tuning range 87.5 – 108.0 MHz

Antenna FM wire antenna

Antenna terminals 75 ohms, unbalanced

Intermediate frequency

10.7 MHz

AM tuner section

Tuning range

Antenna Loop antenna

Intermediate frequency

450 kHz

General

Power requirements

Power output (DIGITAL MEDIA PORT)

DC OUT: 5 V, 700 mA MAX

Area code Power requirements

UC 120 V AC, 60 Hz

MX 127 V AC, 60 Hz

Area code Tuning scale

10 kHz step 9 kHz step

UC, MX 530 –

1,710 kHz

531 –

1,710 kHz

Area code Power requirements

UC 120 V AC, 60 Hz

MX 127 V AC, 60 Hz

continued

Contents

Main To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. For customers in the United States, Canada and Mexico For customers in the United States WARNING Owners Record Important Safety Instructions CAUTION About This Manual On Copyrights The HT-SF360 consists of: About area codes Table of Contents Getting Started Playback Amplifier Operations Enjoying Surround Sound Description and location of parts Front panel 25641 73 Indicators on the display 2 4 5 61 3 7 8 9q;qaqsqd Rear panel 1 2 5 6 734 ASPEAKERS section BS-AIR (EZW-T100) CDMPORT Remote commander 1 3 2 6 7 8 q; qa 9 1 C (TV, BD, DVD, or SAT) to select the component you want to operate. The component assigned to the selected input button becomes operable. 2 press the corresponding button for the operation. To control the DVD recorder/Blu-ray Disc recorder To control the DVD player/ Blu-ray Disc player To control the HDD/DVD COMBO To control the SAT 1: Installing the speakers Example of subwoofer Getting Started Installing the speakers on a flat surface Installing the speakers on the speaker stand You can install your speakers on the wall. 1 For the front speakers that are suitable for the hook on the back of each speaker. See the illustrations below. 2 The screws should protrude 7/32 to 9/32 inch. 2: Connecting the speakers Note on speaker cords D ASpeaker cord (supplied) E 3: Connecting the TV BC BOptical digital cord (not supplied) CHDMI cable (not supplied) 4: Connecting the audio/ video components Component to be connected B How to hook up your components Connecting audio components Connecting components with HDMI jacks Notes on HDMI connections AAA AHDMI cable (not supplied) BOptical digital cord (not supplied)b) CAudio cord (not supplied)b) ABC Connecting video components BC BCoaxial digital cord (not supplied) COptical digital cord (not supplied) 5: Connecting the antennas 6: Preparing the receiver and the remote 1,2 1 2 7: Calibrating the appropriate settings automatically (AUTO CALIBRATION) Inserting batteries into the remote 1 microphone to the AUTO CAL MIC jack. 2 microphone. Before you perform Auto Calibration 2 A.CAL. 3 START appears on the display. 4 1 result. When the measurement ends, a beep sounds and the measurement result appears on the display. 2 the item. Then, press . 2 A.CAL appears, then press or b. 3 A.CAL CLR, then press or b. 4 8: Adjusting the speaker levels (TEST TONE) 2 3 4 Selecting a component 1 a component. You can also use INPUT SELECTOR on the receiver. The selected input appears on the display. 2 Enjoying sound/images from the components connected to the receiver 1 program. For details, refer to the operating 2 3 4 Page 1 2 Navigating through menus 2 3 4 5 Amplifier Operations Overview of the menus Page Amplifier Operations Settings for the HDMI (SET HDMI menu) SET HDMI menu parameters xCONTROL FOR HDMI (Control for HDMI) xVOL LIM (Volume limit) Settings for the Speaker (SP SETUP menu) SP SETUP menu parameters Adjusting the level (LEVEL menu) LEVEL menu parameters Adjusting the tone (TONE menu) Settings for the Custom Menu (CUSTOM menu) CUSTOM menu parameters xDUAL (Digital broadcast language selection) xA/V SYNC (Synchronizes audio with video output) Settings for the S-AIR (S-AIR menu) Enjoying Surround Sound Selecting the sound field Press SOUND FIELD repeatedly to select the sound field you want. For details, see Types of sound field available (page 41). Types of sound field available Enjoying Surround Sound Listening to FM/AM radio 1 select the FM or AM band. You can also use INPUT SELECTOR on Tuner Operations 2 If an FM program is noisy 1 2 MODE appears, then press 3 2 TUNING until the auto scanning starts. 3 4 MEMORY appears in the display. Presetting radio stations Page 6 V/v/B/b. If you enter a wrong character 7 8 Preparing for the BRAVIA Sync When your TV is compatible with the Control for HDMI-Easy Setting function 1 2 3 When your TV is not compatible with the Control for HDMI-Easy Setting function 1 2 3 4 5 6 Playing back components with one-touch operation (One-Touch Play) Play back a connected component. Watching a DVD/Blu-ray disc by simple operation Enjoying the TV sound from the speakers connected to the receiver 2 HDMI appears, then press 3 LIM appears, then press or b. 4 Using the Power Saving function (Power Save) The AMP MENU turns off. SET HDMI appears on the display. 2 Page Page Using an S-AIR Product About S-AIR products Inserting the wireless transmitter/transceiver To insert the wireless transmitter into the S-AIR main 1 2 3 To insert the wireless transceiver into the S-AIR sub To set the ID of the S-AIR main S-AIR ID. the desired ID (A, B or C) then To exit the menu 1 2 3 4 5 6 1 to match the S-AIR main unit. 2 3 4 5 7 the setting you want. 8 the S-AIR product. 9 2 3 4 5 6 2 3 4 5 6 Changing the input button assignments 1 which you want to change the assignment. Using the Remote 2 press the corresponding button for the category you want. Categories and the corresponding buttons for BD, DVD, and SAT To clear all remote button assignments Glossary xDTS Digital Surround xHDMI (High-Definition Multimedia Interface) xL.F.E. (Low Frequency Effects) xS-AIR (Sony Audio Interactive Radio frequency) xS-master Precautions On safety On power sources On heat buildup On placement Troubleshooting Audio Video HDMI S-AIR function Tuner Remote control Others Error messages If you are unable to remedy the problem using the troubleshooting guide If the problem persist Specifications AUDIO POWER SPECIFICATIONS FM tuner section AM tuner section General Speaker section Page Index A B C D