Sony HT-SS1000 Specifications

Specifications

Amplifier section

HT-SF1000 only

Power Output1)

Stereo mode (rated) 70 W + 70 W

(4 ohms at 1 kHz, 0.7%)

Music power output (reference) FRONT2): 143 W/ch (With SS-FSP1000) CENTER2): 143 W (With SS-CNP1000F) SUR2): 143 W/ch (With SS-FRP1000) SUBWOOFER2): 285 W (With SS-WP1000)

HT-SS1000 only

Power Output1)

Stereo mode (rated) 70 W + 70 W

(4 ohms at 1 kHz, 0.7%)

Music power output (reference) FRONT2): 143 W/ch (With SS-MSP1000) CENTER2): 143 W (With SS-CNP1000) SUR2): 143 W/ch (With SS-SRP1000) SUBWOOFER2): 285 W (With SS-WP1000)

1)Measured under the following conditions:

Area code	Power requirements
CEL, CEK, AR, SP	230 V AC, 50 Hz

AU, E51	240 V AC, 50 Hz

MX	127 V AC, 60 Hz

2)Depending on the sound field settings and the source, there may be no sound output.

Inputs (Analog)

SA-CD/CD,	Sensitivity: 1 V
VIDEO 1, 2	Impedance: 50 kohms

Inputs (Digital)

	DVD (Coaxial)	Sensitivity: –
		Impedance: 75 ohms

	VIDEO 2, SA-CD/	Sensitivity: –
	CD (Optical)	Impedance: –

	Reproduction frequency range:
		28 – 20,000 Hz
	Tone

	Gain levels	±6 dB, 1 dB step

	FM tuner section
	Tuning range	87.5 - 108.0 MHz
	Antenna	FM wire antenna
	Antenna terminals	75 ohms, unbalanced
	Intermediate frequency
		10.7 MHz
	AM tuner section
	Tuning range
	Models of area code CEL, CEK, AU, SP
	With 9-kHz tuning scale:
		531 – 1,602 kHz
	Models of area code E51
	With 10-kHz tuning scale:
		530 – 1,610 kHz3)
	With 9-kHz tuning scale:
	With 9-kHz tuning scale:
		531 – 1,602 kHz3)
		531 – 1,602 kHz3)			Additional
	Models of area code AR, MX
	With 10-kHz tuning scale:
	With 10-kHz tuning scale:
		530 – 1,610 kHz
	Antenna	Loop antenna
	Intermediate frequency				Information
	the receiver. While holding down PRESET				Information
		450 kHz

3)You can change the AM tuning scale to 9 kHz or 10 kHz. After tuning in any AM station, turn off

TUNING +, press ?/1. All preset stations will be erased when you change the tuning scale. To reset the scale to 10 kHz (or 9 kHz), repeat the procedure.

continued

57GB

Contents

Page WARNING For customers in Europe About This Manual Table of Contents Description and location of parts Front panel About the indicators on the display Page Rear panel RM-AAU006 Page Page 1: Installing speakers HT-SS1000only Example of HT-SS1000front speaker Installing the speakers on the 3 Hang the speakers on the screws 2: Connecting speakers Notes on speaker cords Note on speakers 3: Connecting the audio/video components Component to be connected Connecting audio components If you connect a DVD recorder Notes on HDMI connections 4: Connecting the antennas 5:Preparing the receiver and the remote 6: Calibrating the automatically appropriate settings Performing Auto Calibration Press AUTO CAL Error codes To rectify the error Error code and remedies Warning codes To change the settings manually 7:Adjusting the speaker levels and balance To turn off the test tone Selecting a component To mute the sound To avoid damaging your speakers Listening/Watching a component Watching a DVD 1 Turn on the TV and DVD player 3 Press DVD 4 Switch the input of the TV so that an image of the DVD is displayed 5 Set up the DVD player Navigating through menus To return to the previous display To exit the menu Overview of the menus Page Adjusting the level LEVEL menu parameters Adjusting the tone TONE menu parameters Settings for the surround sound SUR menu parameters Settings for the tuner Settings for the audio TUNER menu parameters AUDIO menu parameters Settings for the system SYSTEM menu parameters xSL DIST. (Surround left speaker distance) xSR DIST. (Surround right speaker distance) xSUR PL (Surround speaker placement) Calibrating the appropriate settings automatically Enjoying Dolby Digital and DTS Surround sound Types of A.F.D. mode Selecting a preprogrammed sound field Types of sound field available About DCS (Digital Cinema Sound) About CINEMA STUDIO EX modes To turn off the surround effect for movie/music Listening to FM/AM radio In case of poor FM stereo reception If you cannot tune in a station Storing FM stations automatically Presetting radio stations Using the controls on the receiver Displaying RDS information While receiving an RDS station, press DISPLAY repeatedly Description of program types Using the Sleep Timer Changing button assignments Categories and the corresponding buttons To clear all remote button assignments Glossary Precautions On safety On power sources On heat buildup On placement If color irregularity is observed again If howling occurs On cleaning Troubleshooting Page Remote control Error messages If you are unable to remedy the problem using the troubleshooting guide If the problem persist Reference sections for clearing the receiver’s memory Specifications Page Page Index