Connections (Continued)

Speaker System Connections

Connect the speakers using the supplied speaker cords by matching the colors of the terminals and those of the cords. To obtain the best possible surround sound, adjust the speaker parameters (distance, level, etc.).

Notes

Be sure to match the speaker cord to the appropriate terminal on the components: 3 to 3 and # to #. If the cords are reversed, the sound will be distorted and lack bass.

If you use front speakers with low maximum input rat- ing, adjust the volume carefully to avoid excessive volume output to the speakers.

Do not disassemble the front covers of supplied speakers.

 

 

 

 

 

 

Front Speaker

 

 

Center

Front Speaker

 

 

 

 

 

 

 

(Right)

 

Speaker

 

 

(Left)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Rear speaker

Rear speaker

(Right surround)

(Left surround)

 

Subwoofer

About Ferrite Core

1

Be sure to attach the ferrite core to

the speaker cables (for connecting to

this unit).

This ferrite core can reduce noises.

2

How to attach the ferrite core.

 

 

1 Push the stopper [a] of the ferrite core

3

to open.

2 Wind the Center and Subwoofer Speaker

 

 

cables once on the ferrite core.

 

Pass the others straight on the ferrite core.

 

3 Close the ferrite core until it clicks.

Speaker Positioning

For a normal setup use 6 speakers (2 front speakers, center speaker, 2 rear speakers and subwoofer).

Front Speakers

 

PREPARATION

 

 

 

Based on your listening position, set up the speakers

 

 

at equal distance. And by hearing position, set up an

 

 

interval between speakers of 45 degree.

 

 

Center Speaker

 

 

 

It is ideal that the center speakers and front speakers

 

 

are same height. But normally place it above or below

 

 

the television as shown below.

 

 

Rear Speakers

 

 

 

Place the rear surround speakers to the left and right

 

 

behind the primary listening area. These speakers

 

 

recreate sound motion and atmosphere required for

 

 

surround playback. For best results, do not install the

 

 

rear speakers too far behind the listening position,

 

 

install them at or above the level of the listener’s ears.

 

 

It is also effective to direct the rear speakers towards

 

 

a wall or ceiling to further disperse the sound.

 

 

In the case of a smaller room size, if the audience is

 

 

near to the rear wall set the rear speakers opposite

 

 

each other, and set the rear speakers 60 - 90 cm

 

 

above the listener’s ears.

 

 

• Subwoofer

 

 

 

This can be placed in any front position.

 

 

 

Subwoofer

 

 

 

 

 

 

Center Speaker

 

 

 

Front

 

 

 

 

 

Front

 

 

 

 

 

 

 

 

 

 

 

 

Speaker

Speaker

 

 

(Left)

(Right)

 

Rear

 

 

 

 

 

 

 

 

 

 

 

 

Rear

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Speaker

Speaker

 

(Left)

(Right)

 

Speaker Positioning Example

Note

Speaker stand is optional.

13