Adjustment Using the Menus
28
About the function assigned to the function button
SCAN
Press the button to change the scan size of the picture.
With every press of the button, the picture switches in
the sequence NORMAL scan t OVER scan t
NATIVE (see “Scan mode image” on page 29).
ASPECT
Press the button to set the aspect ratio of the picture, 4:3
or 16:9.
BLUE ONLY
Press the button to eliminate the red and green signals.
Only blue signal is displayed as an apparent
monochrome picture on the screen. This facilitates
“chroma” and “phase” adjustments and observation of
signal noise.
MONO
Press the button to display a monochrome picture. When
the buttons is pressed again, the monitor switches
automatically to color mode.
MARKER
Press the button to display the marker. Set the aspect
marker in the MARKER SETTING menu (see page 24).
H/V DELAY
Press the button to observe the horizontal and vertical
sync signals at the same time.
CLOSED CAP.
Press the button to display the closed caption. Set the
closed caption setting in the CLOSED CAPTION
SETTING menu (see page 29).
WFM/ALM/VS (WFM/ALM/VECTOR)
Press the button to display the WFM/ALM/vectorscope
display. Set the WFM/ALM/vectorscope display setting
in the WFM/ALM/VECTOR SETTING menu (see
page 26).
When LINE SELECT is set to ON and WFM is selected,
each time you press the button, the settings change in the
sequence WFM display activated t Line position
setting t WFM display deactivated. Turn the menu
selection control to move the line, when the line position
is selected.
When LINE SELECT is set to OFF, the WFM display
switches between activated and deactivated.
ZOOM
Press the button to zoom in the WFM/ALM/vectorscope
display. Set the ZOOM setting in the WFM/ALM/
VECTOR SETTING menu (see page27).
BRIGHTNESS
Press the button to adjust the picture brightness. Press
the button to display the adjustment screen and adjust
the picture brightness. Press again to hide the adjustment
screen. However, the picture brightness remains
adjustable. Turn the menu selection control right to
increase the brightness and turn left to decrease it.
CONTRAST
Press the button to adjust the picture contrast. Press the
button to display the adjustment screen and adjust the
picture contrast. Press again to hide the adjustment
screen. However, the picture contrast remains
adjustable. Turn the menu selection control right to
increase the contrast and turn left to decrease it.
CHROMA
Press the button to adjust the color intensity. Press the
button to display the adjustment screen and adjust the
color intensity. Press again to hide the adjustment
screen. However, the color intensity remains adjustable.
Turn the menu selection control right to increase the
intensity and turn left to decrease it.
VOLUME
Press the button to adjust the volume. Press the button to
display the adjustment screen and adjust the volume.
Press again to hide the adjustment screen. However, the
volume remains adjustable. Turn the menu selection
control right to increase the volume and turn left to
decrease it.
I/P MODE
Press the button to set the delay by the picture
processing to the minimum level when interlace signal
is input. The mode switches in the sequence INTER-
FIELD t FIELD MERGE t LINE DOUBLER t
INTRA-FIELD with every press of the button (see “I/P
MODE” on page 23).
PHASE
Press the button to adjust the color tones. Press the
button to display the adjustment screen and adjust the
color tones. Press again to hide the adjustment screen.
However, the color tones remain adjustable. Turn the
Submenu Setting
F1 BUTTON to F7
BUTTON
Assigns the function to the function
buttons of the front panel and turns the
function on or off.
You can assign the function from among
SCAN, ASPECT, BLUE ONLY,
MONO, MARKER, I/P MODE, etc.
Factory setting
•F1 button: BRIGHTNESS
•F2 button: CONTRAST
•F3 button: CHROMA
•F4 button: SCAN
•F5 button: H/V DELAY
•F6 button: VOLUME
•F7 button: I/P MODE