Sony MZ-N1 service manual 000 P * * R, Push, 000 JOG+OK, Jog Ok

Sound Skip Check Result Display Mode

This set can display the count of errors that occurred during the recording/playing for checking.

•Setting method of sound skip check result display mode

1.Set the test mode (see page 13).

2.Press the N key or [REC] key, and the playing or recording sound skip result display mode becomes active respectively where the LCD displays the following.

Remote commander LCD display

000P * * R * *

Total count of record system errors (hex.)

Total count of play system errors (hex.)

3.When the N key is pressed, total error count is displayed on the LCD, and each time the > key is pressed, the display item moves down by one as shown below. Also, if the . key is pressed, the display item moves up by one, then if the [REC] key is pressed, the display in the record mode appears.

When the [REC] key is pressed, total error count is displayed on the LCD, and each time the > key is pressed, the display item moves down by one as shown below. Also, if the . key is pressed, the display item moves up by one, then if the N key is pressed, the display in the play mode appears.

Playing sound skip	Recording sound skip
result display	result display

MZ-N1

Jog and Key Check Mode

This set can check if the set and remote commander function nor- mally.

• Setting method of jog check mode

1.Set the test mode (see page 13).

2.Press the jog button to activate the jog check mode and display as below.

Remote commander LCD display

000PUSH

3.Turn the jog dial downwards one click.

Remote commander LCD display

000JOG+ 1

4.Turn the jog dial downwards three more clicks.

Remote commander LCD display

000JOG+OK

5.Turn the jog dial upwards one click.

Remote commander LCD display

000 JOG- 1

000P * * R * *

000 E I B * *

000S t a t * *

000A d r s * *

000B E m p * *

000# # # # # #

000P * * R * *

000B O v r * *

000B f u l * *

000R t r y * *

000# # # # # #

6.Turn the jog dial upwards three more clicks.

Remote commander LCD display

000 JOG OK

7.When the x/CHG key is pressed, it changes over to the key check mode.

Note: To enter the key check mode, it is not necessary to enter via the jog dial check mode. (Refer to next item)

• Setting method of key check mode

1.	Set the test mode (see page 13).
2.	Press the [T MARK] key or [DISPLAY] key on the remote com-
	mander for several seconds (about 3 seconds) activates the key
	check mode. (At the last two digits, AD value of remote com-
	mander key line is displayed in hexadecimal)

P**R**: Total play/record errors (hex.)

**: Counter of sound skip check each item (hex.)

######: 6-digit address where sound was skipped last (hex.)

• Cause of sound skip error

	Cause of error	Description of error
	EIB	Sound error correction error
Play	Stat	Decoder status error
	Adrs	Address access error
	BEmp	Buffer is empty
	BOvr	Buffer is full, and sounds were
		dumped
Record	Bful	Buffer capacity becomes less,
		and forcible writing occurred
	Rtry	Retry times over

4.To quit the sound skip check result display mode and to return to the test mode (display check mode), press the x/CHG key.

Remote commander LCD display

000**

**: AD value of the remote commander key (hexadecimal 00 to FF)

3.When each key on the set and on remote commander is pressed, its name is displayed on the remote commander LCD. (The operated position is displayed for 4 seconds after the slide switch is operated. If any other key is pressed during this dis- play, the remote commander LCD switches to its name dis- play)

17