•IC801
Pin No. | Pin Name | I/O |
|
| Description |
| ||
|
|
|
|
| ||||
1 | NC | O | Load address strobe signal output terminal for | Not used | ||||
|
|
|
|
|
|
|
| |
2 | NC | I | Test input terminal for | Not used |
|
|
| |
|
|
|
|
|
|
| ||
3 to 7 | NC | O | Address signal output terminal for | Not used |
|
| ||
|
|
|
|
|
|
| ||
8, 9 | NC | I/O | Not used |
|
| |||
|
|
|
|
|
|
| ||
10, 11 | DRAMVDD0, 1 | — | Power supply terminal (for |
|
|
| ||
12, 13 | DRAMVSS0, 1 | — | Ground terminal (for |
|
|
|
|
|
14, 15 | NC | I/O | Not used |
|
| |||
16 to 19 | NC | O | Address signal output terminal for | Not used |
|
| ||
|
|
|
|
| ||||
20 | NC | O | Column address strobe signal output terminal for | Not used | ||||
|
|
|
|
|
|
|
| |
21 | NC | I | Test input terminal for | Not used |
|
|
| |
|
|
|
|
|
|
| ||
22, 23 | NC | O | Address signal output terminal for | Not used |
|
| ||
|
|
|
|
|
|
|
| |
24 | DVSS0 | — | Ground terminal (for the DSP block) |
|
|
|
| |
25 | DVDD0 | — | Power supply terminal (for the DSP block) (+1.5V) |
|
| |||
26 | OFTRK | I | Off track signal input from the DSP monitor (3) |
|
| |||
|
|
|
| |||||
27 | SSB DATA | I/O | SSB data input/output with the RF amplifier and the remote commander attached headphone | |||||
|
|
|
|
|
|
|
| |
28 | SSB CLK | O | SSB clock output to the RF amplifier |
|
|
|
| |
|
|
|
| |||||
29 | VREC PWM | O | PWM signal output for the Over write head drive power supply voltage control to the power | |||||
control |
|
|
|
|
| |||
|
|
|
|
|
|
|
| |
|
|
|
| |||||
30 | VL PWM | O | PWM signal output for the laser power supply voltage control to the power control | |||||
31 | VC PWM | O | PWM signal output for the system power supply voltage control to the power control | |||||
32 | NC (VD PWM) | O | VD power supply voltage control signal output terminal | Not used | ||||
|
|
|
|
|
|
|
|
|
33 | NC | — | Not used |
|
|
|
|
|
|
|
|
| |||||
34 | IFVDD0 | — | Power supply terminal (for the microcomputer I/F block) (+2.3V) | |||||
|
|
|
|
|
| |||
35 | IFVSS0 | — | Ground terminal (for the microcomputer I/F block) |
|
| |||
|
|
|
|
|
| |||
36 | OPT DET | I | DIN plug detection signal input terminal | “H”: DIN plug |
| |||
37 | XJACK DET | I | LINE IN plug detection signal input terminal | “L”: LINE or OPT plug | ||||
38 | XMIC DET | I | Microphone plug detection signal input terminal “L”: microphone plug Not used | |||||
39 | OPEN CLOSE | I | Open/close detection switch of the upper panel input terminal | |||||
SW | “L”: when upper panel close |
|
|
|
|
| ||
|
|
|
|
|
|
| ||
|
|
|
|
|
| |||
40, 41 | SET CODE0, 1 | I | Input terminal for the set (fixed at “L” in this set) |
|
| |||
|
|
|
|
|
|
|
| |
42 | SET CODE2 | I | Input terminal for the set (open in this set) |
|
|
|
| |
|
|
|
|
|
| |||
43 | SET CODE3 | I | Input terminal for the set (fixed at “L” in this set) |
|
| |||
44 | XPATCH | I | Patch function detection signal input terminal | “L”: patch function Not used | ||||
45 | SI0 | I | Serial data input from the nonvolatile memory |
|
| |||
46 | SO0 | O | Serial data output to the nonvolatile memory, A/D converter and liquid crystal display element | |||||
module |
|
|
|
|
| |||
|
|
|
|
|
|
|
| |
|
|
|
| |||||
47 | SCK0 | O | Serial clock signal output to the nonvolatile memory, A/D converter and liquid crystal display | |||||
element module |
|
|
|
|
| |||
|
|
|
|
|
|
|
| |
|
|
|
|
| ||||
48 | XGUM ON | I | Rechargeable battery detection switch input terminal | “L”: there is rechargeable battery | ||||
Not used |
|
|
|
|
| |||
|
|
|
|
|
|
|
| |
|
|
|
| |||||
49 | BEEP | O | Beep sound control signal output to the headphone amplifier | |||||
50, 51 | TEST1, TEST0 | I | Input terminal for the main test (normally fixed at “L”) |
|
| |||
52 | KDO | O | Data output terminal Not used |
|
|
|
|
|
|
|
|
|
|
|
|
| |
53 | KRB | I | Ready/busy signal input terminal | Not used |
|
|
| |
|
|
|
|
|
|
|
| |
54 | KCLK | O | Clock signal output terminal Not used |
|
|
|
| |
|
|
|
|
|
|
|
| |
55 | KCS | O | Chip select signal output terminal | Not used |
|
|
| |
|
|
|
|
|
|
|
|
|
49
