MZ-N510CK
Modulation system
EFM (Eight to Fourteen Modulation)
Frequency response
20 to 20,000 Hz – 3 dB
Inputs1)
Line in:
stereo
Outputs
i: stereo
Maximum output level
5 mW + 5 mW; load impedance
16Ω (except USA),24Ω ( Ο nly USA)
Power requirements
Sony AC Power Adaptor connected at the DC IN 3V jack:
120 V AC, 60 Hz (Models for USA, Canada and Mexico)
The recorder:
Dimensions
Approx. 81.0 ⋅ 27.7 ⋅ 74.4 mm (w/h/d) (31/4 ⋅ 11/8 ⋅ 3 in.)
Mass
Approx. 103 g (3.6 oz) the recorder only
1)The LINE IN (OPTICAL) jack is used to connect either a digital (optical) cable or a line (analog) cable.
2)The i jack connects either headphones/ earphones or a line cable.
3)Measured in accordance with JEITA.
Car connecting pack
Frequency response: 50 to 20,000Hz (Differs depending on your car cassette deck) Dimensions: Approx. 102.4 ⋅ 12.1 ⋅ 63.8 mm (w/h/d) (41/8 ⋅ 1/2 ⋅ 25/8 in.)
Mass: Approx. 42 g (1.5 oz)
Cord length: Approx. 1.5 m
Car battery cord
Input voltage: DC 12 V/24 V (only for negative
#ground cars)
Rated output voltage: DC 3.0 V
Rated output current: 1,000 mA
Dimensions: Approx. 36.0 ⋅ 26.2 ⋅ 101.1 mm (w/h/d) (17/16 ⋅ 11/16 ⋅ 4 in.) including projecting parts
Mass: Approx. 60 g (2.2 oz)
Cord length: Approx. 1.5 m
Checking the supplied accessorie
AC power adaptor (1) Headphones/earphones (1) Dedicated US cable (1) Rotary commander (1)
Car battery cord (1) Car connecting pack (1)
Carrying case with Velcro strips (1)
∗Do not play a
Design and specifications are subject to change without notice.
Battery life
The battery life may be shorter due to operating conditions, the temperature of the location, or alkaline dry battery you use.
(Unit: approx.hours)(JEITA1))
LR6 (SG) | Normal | LP2 | LP4 |
alkaline dry |
|
|
|
battery2) |
|
|
|
Recording3) | 10 | 14 | 18.5 |
Playback | 42 | 48 | 56 |
|
|
|
|
1)Measured in accordance with the JEITA (Japan Electronics and Information Technology Industries Association) standard.
2)When using a Sony LR6 (SG) STAM INA alkaline dry battery (produced in Japan).
3)To prevent interrupted recording due to drained battery, use new battey for recording operations.
When to replace the battery
When the dry battery is weak, flashing
ror L OW BATT a ppears in the display. Replace the dry battery.
The battery level indicator is approximate. It may be more or less than the indication depending on the operating condition.
Note
Stop the recorder before replacing battery.
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- LISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
2
