Completing A/V hookup:

After you’ve connected your TV and completed antenna or cable hookup, return to this procedure to complete VCR set up. This will prevent unwanted noise in the RF channel.

Press MENU and select

 

 

Set AUTO ANT SELECT

ADVANCED OPTIONS.

 

 

to OFF and press OK.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TIMER SET/CHECK

 

 

 

 

 

 

ADVANCED OPTIONS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SETTINGS

 

 

 

 

 

AUTO ANT SELECT

ON

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

AUTO STEREO

OFF

 

 

 

 

 

 

 

 

 

 

 

 

 

ADVANCED OPTIONS

 

 

 

 

 

 

 

 

 

 

,

 

 

 

TUNER AUDIO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

APC

 

 

 

 

 

ON

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TAPE SELECT

AUTO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

AUTO TAPE SPEED

ON

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FAVORITE CH

ON

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SHARPNESS

L

 

H

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RETURN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SELECT :

 

 

 

 

 

 

 

SELECT :

 

 

 

 

 

 

 

 

 

SET

:

 

OK

 

 

 

 

 

 

SET

:

 

OK

 

 

 

 

 

 

 

 

QUIT

:

 

MENU

 

 

 

 

 

QUIT

:

 

MENU

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

For details, see page 68.

Caution

Connections between the VCR’s VHF/UHF connector and the antenna terminals of the TV receiver should be made only as shown in the following instructions. Failure to do so may result in operation that violates the regulations of the Federal Communications Commission regarding the use and operation of RF devices. Never connect the output of the VCR to an antenna or make simultaneous (parallel) antenna and VCR connections at the antenna terminals of your receiver.

Note to CATV system installer (in USA)

This reminder is provided to call the CATV system installer’s attention to Article 820- 40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

Started Getting

Hookups 9