5.Input select operation check using the TEST button
1Do not input any signal to LINE4 INPUT of the SRP- X700P. Select VIDEO using the signal format select button
and press the TEST button in the INPUT SELECT command setup.
2Confirm that VIDEO is selected as the input signal to the projector.
3Execute the same confirmation as in steps 1 and 2 for all signal systems.
If the input selection is not executed correctly, check for erroneous entry of the COMMAND1 and COMMAND2 commands in the port setup and in the INPUT SELECT command setup.
If the setup is confirmed to be correct, make the setup time of WAIT1 setup box longer in increments of a single step and confirm the operation. Select the time at which input signal can be correctly operated.
6.Operation check using the LINE4 SELECT button of the SRP-X700P
1Set up the SIGNAL DEFINE setup box on the REMOTE screen to a practical setup that can be actually used.
2Input signals to all channels of LINE4 INPUT of the SRP- X700P. Operate the LINE4 SELECT button and confirm
that the video signal is displayed from the projector.
3Operate the LINE4 SELECT button in all operation patterns of A tB, A tC, A tD, A tE, A tF······
F tA, F tB, F tC, F tD and F tE to confirm that the video signal is displayed from the projector.
4Operate the LINE4 SELECT button several times randomly and confirm that the video signal of the button last pressed is displayed.
If the video signal is not displayed, check the setup of the SIGNAL DEFINE setup box on the REMOTE screen and check the setups of the projector itself.
If the setup is confirmed to be correct, adjust the setup time of the WAIT setup box as follows.
1Make the setup times of both WAIT1 and WAIT2 longer in increments of a single step and confirm the operation. Select the time at which the input signal can be correctly
selected.
2Make the setup time of WAIT1 shorter in increments of a
single step and confirm the operation. Select the time at which input signal can be correctly selected.
3Make the setup time of WAIT2 shorter in increments of a single step and confirm the operation. Select the time at which input signal can be correctly selected.
zIf you want to shorten the time before the video signal is displayed after operating the LINE4 SELECT button, set the WAIT1 and WAIT2 setup times to the shortest time first. Then perform “5. Input select operation check using the TEST button” and “6. Operation check using the LINE4 SELECT button of the
7.PROJECTOR POWER ON operation check
1Press the LINE4 SELECT button “A” of the
signal.
2Operate the input select switch of the projector so that the projector does not display the video output signal.
3Operate the POWER switch of the projector so that the projector enters standby.
4After confirming that the projector enters standby, press the TEST button of the PROJECTOR POWER ON setup.
5Confirm that the projector power is turned on and the LINE4 INPUT A video signal is displayed.
6Repeat the confirmation operations as in steps 1 to 5 for the LINE4 INPUT B to F.
If the main power cannot be turned on, check whether the commands in the COMMAND setup box are correct.
If the video signal is not displayed, make the WAIT setup box of the PROJECTOR POWER ON setup longer in increments of a single step and confirm the operation. Set the WAIT setup box for normal operation.
zIf you want to shorten the time before the video signal is displayed after turning on the projector, make the WAIT1 setup time shorter and set it for normal operation.
8.PROJECTOR POWER STANDBY operation check
1Press the TEST button of the PROJECTOR POWER STANDBY setup and confirm that the projector enters the
power standby state.
2Press the TEST button of the PROJECTOR POWER ON
setup to turn on the power of the projector.
3Press the LINE4 SELECT button “A” of the
signal.
4About 3 seconds after pressing the TEST button of the PROJECTOR POWER ON setup, press the TEST button of
the PROJECTOR POWER STANDBY setup.
5Confirm that the projector starts the power standby
operation.
6Confirm that the projector power is turned on and the LINE4 INPUT A video signal is correctly displayed.
If the projector power cannot enter the standby state, check whether the commands in the COMMAND setup box are correct.
If the projector power cannot be turned on, make the WAIT setup box of the PROJECTOR POWER STANDBY setup longer in increments of a single step and confirm the operation. Select the time at which the projector power cannot be turned on correctly.
25