NWZ-A826/A826K/A828/A828K/A829
Pin No. | Pin Name | I/O | Description | |
D2 | NAND_RBZ0 | O | Read/busy signal output to the NAND flash memory | |
D3 | NAND_ALE | O | Address latch enable signal output to the NAND flash memory | |
D4 | NAND_DA2 | I/O | ||
D5 | IO_B | - | Not used | |
D6, D7 | VDD_L1 | I | Power supply input terminal (+1.2V) | |
D8 | GND | - | Ground terminal | |
D9 | NC | - | Not used | |
D10 | GND | - | Ground terminal | |
D11 to D14 | NC | - | Not used | |
D15 | SWVBUS2 | - | Not used | |
D16 | CAPVBSW | - | Not used | |
D17 | VCCVBAT | I | Power supply input terminal (+2.3 - 4.2V) | |
D18 | AB0_A3 | O | Address signal output to the USB controller | |
D19 | IO_A | - | Not used | |
D20 | AB0_A6 | O | Address signal output to the USB controller | |
D21 to | NC | - | Not used | |
D23 | ||||
|
|
| ||
D24, D25 | AB0_D0, AB0_D2 | I/O | ||
D26 | NC | - | Not used | |
E1 | DISCHGVBUS | - | Not used | |
E2 | NC | - | Not used | |
E3 | NAND_REZ | O | Read enable signal output to the NAND flash memory | |
E4 | NAND_DA3 | I/O | ||
E5 | IO_B | - | Not used | |
E6 | NAND_DA5 | I/O | ||
E7 | NC | - | Not used | |
E8 | NAND_DA7 | I/O | ||
E9 | NAND_CLE | O | Command latch enable signal output to the NAND flash memory | |
E10 | BATSEL | - | Not used | |
E11 | SWBAT | - | Not used | |
E12 | CAPBTDL | - | Not used | |
E13 | CAPADDL | - | Not used | |
E14 | NC | - | Not used | |
E15 | SWVBUS | - | Not used | |
E16, E17 | NC | - | Not used | |
E18 | AB0_A4 | O | Address signal output to the USB controller | |
E19 | FLASHCLK | O | Clock signal output terminal Not used | |
E20 | AB0_A7 | O | Address signal output to the USB controller | |
E21 to E23 | NC | - | Not used | |
E24 | AB0_XDMARQ | I | Request signal input from the USB controller | |
E25 | AB0_D4 | I/O | ||
E26 | NC | - | Not used | |
F1 | DGND | - | Ground terminal | |
F2 | CHGVBUS | - | Not used | |
F3, F4 | NC | - | Not used | |
F5 | IO_B | - | Not used | |
F22 | AB0_CSZ2 | O | Chip select signal output to the USB controller | |
F23 | AB0_DACK | O | Acknowledge signal output to the USB controller | |
F24, F25 | AB0_D3, AB0_D5 | I/O | ||
F26 | NC | - | Not used | |
G1 | DVDD | I | Power supply input terminal (+2.85V) | |
G2, G3 | NC | - | Not used | |
G4 | EXTRST | I | RESET switch input terminal | |
G5 | NC | - | Not used | |
G22 | ETHER_XINT | - | Not used |
36
