AA35 MIXER AMPLIFIER | OWNER'S MANUAL |
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
|
|
|
|
|
|
|
|
Zone 2 Assign | Mute Rcv | Phantom | Input1 | Low cut | |||
|
|
|
|
|
|
|
|
Input 3 | Input 2 | Input 1 | Input 3 | Input 2 |
|
|
|
|
|
|
|
|
|
|
|
Off | Off | Off | Off | Off | Off | Line/Tel | Off |
On | On | On | On | On | On | Mic | On |
SWITCH 6 - Phantom - When "ON", applies Phantom Power 24VDC to Input 1 terminals for condenser type microphones. Note: Only use this feature if you are using condenser microphones, otherwise leave in the "OFF" position. This only applies when switch 7 is set to "mic".
SWITCH 7 - Input 1 - When in the "MIC" position, Input 1 will accept microphone level signals; when in the "Line/Tel" position, Input 1 will accept line level or telephone signals.
SWITCH 8 - Low Cut Filter - When in the "ON" position, frequencies below 400Hz are attenuated at the rate of 6dB per octave. Note: The rotary bass control is bypassed when the LOW CUT filter is on. We suggest that when paging horns are connected to the AA35, engage the LOW CUT filter to prevent the horns from operating below their cutoff frequency. When "OFF", the amplifier operates full bandwidth.
12
Unswitched Outlet | Outlet Breaker | Pre Out Line Out A | Input 3 | Input 2 |
120V AC 60Hz | 125V AC 4A |
|
|
|
Max 500W | Push Reset |
|
|
|
LL
77)+
7jbWiIekdZ77I[h_[iC_n[h7 fb_\_[h
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
Zone 2 Assign | Mute Rcv | Phantom | Input1 | Low cut | |||
Input 3 | Input 2 | Input 1 | Input 3 | Input 2 |
|
|
|
Off | Off | Off | Off | Off | Off | Line/Tel | Off |
On | On | On | On | On | On | Mic | On |
| R | R |
|
Amp In | Line Out B |
|
|
|
| Zone 2 Out | |
Speaker Output 35W | 1W |
| |
|
| 8 | 600 |
COM 8 | 25V 70V | - + | - + |
Zone2Mute
0 | 10 | 0 | 10 |
Level |
| Sens | |
Remote |
|
|
|
Mute | Input 1 |
|
|
| G - | + |
|
11
120V AC 60Hz 100W | CLASS 2 WIRING |
| £Èä£Ê>VÊ V >ÞÊ Û`°]ÊÃ]Ê/8ÊÇx££Ê |
|
11.(A) Input 1
Balanced mic or line level signals connect to the (+),
(B) Remote Mute Connector
Shorting the Remote Mute terminals, (G) to (M), will mute inputs 2 and/or 3, depending on how their dipswitch settings are set for switch positions 4 and 5 labeled "Mute Rec"/"Input 2" & "Input 3". In the "ON" position, the corresponding channel will be muted when terminals (G) and (M) are shorted together. This connection is usually done via remote switch on a microphone.
12.Input 2
Input 2 consists of stereo summing inputs, suitable for connection to the output of CD/DVD players, etc.
Specifications are subject to change without notice
AtlasSound.com
1601 JACK MCKAY BOULEVARD ENNIS, TEXAS 75119 U.S.A. • | TELEPHONE: (800) | FAX: (800) | ||
©2006 ATLAS SOUND LP | Printed in U.S.A. | 000106 | ATS002171 RevA 01/06 | PP |
|
|
|
| 8 |
