Abridged Command List
AX | Auto offset X |
AY | Auto offset Y |
AR | Auto offset R |
AP | Auto phase |
B | Return Bandpass Filter Status |
B0 | Take out the Bandpass Filter |
B1 | Put in the Bandpass Filter |
C | Return the Reference LCD Status |
C0 | Display the Reference Frequency |
C1 | Display the Reference Phase Shift |
D | Return Dynamic Reserve Setting |
D0 | Set DR to LOW range |
D1 | Set DR to NORM range |
D2 | Set DR to HIGH range |
En | Return Channel n (1 or 2) Expand |
| Status |
En,0 | Turn Channel n Expand off |
En,1 | Turn Channel n Expand on |
FReturn the Reference Frequency
GReturn the Sensitivity Setting
G1 | Select 10 nV |
... | |
G24 | Select 500 mV |
HReturn Preamp Status (1=installed)
IReturn the Remote/Local Status
I0 | Select Local: Front panel active |
I1 | Select Remote: Front panel inactive |
I2 | Select Remote with full |
J | Set RS232 |
Jn,m,o,p | Set |
K1 | Simulates |
... | (see |
K32 | Simulates |
L1 | Return Status of Line Notch Filter |
L1,0 | Remove Line Notch Filter |
L1,1 | Insert Line Notch Filter |
L2 | Return Status of 2XLine Filter |
L2,0 | Remove 2XLine Notch Filter |
L2,1 | Insert 2XLine Notch Filter |
M | Return the f/2f Status |
M0 | Set reference mode to f |
M1 | Set reference mode to 2f |
N | Return the ENBW setting |
N0 | Select 1 Hz ENBW |
N1 | Select 10 Hz ENBW |
OX | Return X Offset Status |
OX 0 | Turn off X Offset |
OX 1,v | Turn on X Offset, v = offset |
OY | Return Y Offset Status |
OY 0 | Turn off Y Offset |
OY 1,v | Turn on Y Offset, v = offset |
OR | Return R Offset Status |
OR 0 | Turn off R Offset |
OR 1,v | Turn on R Offset, v = offset |
P | Return the Phase Setting |
Pv | Set the Phase to v. Abs(v) <999 deg |
Q1 | Return the Channel 1 output |
Q2 | Return the Channel 2 output |
QX | Return the X Output |
QY | Return the Y Output |
R | Return the trigger mode |
R0 | Set the trigger for rising edge |
R1 | Set the trigger for + zero crossing |
R2 | Set the trigger for falling edge |
S | Return the display status |
S0 | Display X and Y |
S1 | Display X and Y Offsets |
S2 | Display R and Ø |
S3 | Display R Offset and Ø |
S4 | Display X and Y noise |
S5 | Display X5 and X6 (ext D/A) |
T1 | Return |
T1,1 | Set the |
... |
|
T1,11 | Set the |
T2 | Return the |
T2,0 | Remove post filter |
T2,1 | Set the post filter TC to 0.1 S |
T2,2 | Set the post filter TC to 1.0 S |
V | Return the value of the SRQ mask |
Vn | Set the SRQ Mask to the value n |
| (See the Status Byte definition) |
W | Return the RS232 wait interval |
Wn | Set RS232 wait interval to nX4mS |
Xn | Return the voltage at the rear panel |
| analog port n. (n from 1 to 6) |
X5,v | Set analog port 5 to voltage v |
X6,v | Set analog port 6 to voltage v |
Y | Return the Status Byte value |
Yn | Test bit n of the Status Byte |
ZReset to default settings and cancel all pending commands.
7
