Star Micronics Line Thermal Printer

―――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――

STAR Line Mode Command Specifications 5-12

Bit Contents Status By mod el

“0” “1”

TSP800

Ver. 4.3 or

later

TSP700

Ver. 3.2 or

later

TSP600

Ver. 3.2 or

later

TUP900

Ver. 1.2 or

later

TSP1000 TSP828L TSP700II TSP650

7 Fixed at “0” - - - - - - - - -

6 Not Used (Fixed at “0”) - NO NO NO OK NO NO NO NO

5 Not Used (Fixed at “0”) - NO NO NO OK NO NO NO NO

4 Fixed at “0” - - - - - - - - -

3 Presenter Paper Position (See table

below) NO NO NO OK NO NO NO NO

2 Presenter Paper Position (See table

below) NO NO NO OK NO NO NO NO

1 Presenter Paper Position (See table

below) NO NO NO OK NO NO NO NO

0 Fixed at “0” - - - - - - - - -

• This status is valid only on models provided with a presenter. Models not provided with a presenter should send this

status fixed at “0.”

• This status is made valid and invalid using the memory switch only on models provided with a presenter.

When valid, the presenter paper position status is updated, but when invalid, the presenter paper position status is fixed

at “0” and there is no change in status.

• Details of the Presenter Paper Position

bit

Presenter Paper Position

0 0 0 Paper position 0 State where there is no paper in presenter

0 0 1 Paper position 1 State where paper is supplied (loop state)

0 1 0 Paper position 2 (Reserved)

0 1 1 Paper position 3 State where paper is discharged (Can be pulled out)

1 0 0 Paper position 4 (Reserved)

1 0 1 Paper position 5 (Reserved)

1 1 0 Paper position 6 State where paper is recovered

1 1 1 Paper position 7 State where paper is pulled out.

• Presenter operation mode: Paper position status transition

Operating

Mode

Paper Presenter paper position state transition

Loop

Take-up

Recovery Position 0 to Position 1 to (Paper cut) to Position 3 to (Paper recovery) to Position 6 to Position 0

Internal

recovery

Pull out Position 0 to Position 1 to (Paper cut) to Position 3 to (Paper pull out) to Position 7 to Position 0

Loop

Take-up

Recovery Position 0 to Position 1 to (Paper cut) to Position 3 to (Paper pull out) to Position 6 to Position 0

Front

Discharge

Pull out Position 0 to Position 1 to (Paper cut) to Position 3 to (Paper pull out) to Position 7 to Position 0

No Loop Recovery Position 0 to Position 1 to (Paper cut) to Position 3 to (Paper pull out) to Position 6 to Position 0

Internal

recovery

Pull out Position 0 to Position 1 to (Paper cut) to Position 3 to (Paper pull out) to Position 7 to Position 0

No Loop Recovery Position 0 to Position 1 to (Paper cut) to Position 3 to (Paper pull out) to Position 6 to Position 0

Front

Discharge

Pull out Position 0 to Position 1 to (Paper cut) to Position 3 to (Paper pull out) to Position 7 to Position 0

Recovery

Invalid

Recovery Position 0 to Position 1 to (Paper cut) to Position 6 to Position 0

Pull out Position 0 to Position 1 to (Paper cut) to Position 6 to Position 0

4. Note

Do not use ENQ, EOT, and ESC ACK SOH when automatic status is valid. Invalidate the automatic status in advance

using the DIPSW (memory switch) or the ESC RS a n command to query these.