Manuals / Star Micronics / Computer Equipment / Printer

Star Micronics RS232 manual Commands to Control Auto Cutter

Models: RS232

1 80

Download 80 pages 7.65 Kb

Page 56

Manual background

STAR MODE

Commands to Control Auto Cutter
		Full-cut command to the auto cutter
FUNCTION
		<ESC>	“d”	“0”	or <ESC> “d”	<0>
CODE
		1B	64	30	or 1B 64	00
HEX

REMARKS Cuts the paper fully when memory switch 2-C is set to 0. If memory switch 2-C is set to 1, the paper is fed to 18 mm and cut fully. When auto cutter is invalid, this command is not valid.

FUNCTION		Partial-cut command to the auto cutter
		<ESC>	“d”	“1”	or <ESC> “d”	<1>
CODE
		1B	64	31	or 1B 64	01
HEX

REMARKS Cuts the paper partially when memory switch 2-C is set to 0. If memory switch 2-C is set to 1, the paper is fed to 18 mm and cut partially.

– 52 –

Image 56

Star Micronics RS232 manual Commands to Control Auto Cutter

Contents

Thermal Printer TSP200 Series Programmer’s Manual Page TABLE OF CONTENTS Page 1. OUTLINE 2. MEMORY SWITCH AND DIP SWITCH 2-1. Memory Switch2-2. DIP Switch DIP switch arrayStandard DIP switch #1 The factory settings of DIP switch 1 are all onDIP Switch #2 Factory settings 2-1 and 2-2 are on 2-3 and 2-4 are off 3-2. Switches 3-3. Switch Operation Combined Switch Operation3-1. LED 3. DISPLAY PANEL AND FUNCTIONS4-1. Interface Specifications 4. SERIAL INTERFACESERIAL 4-2. Interface Circuit4-2-1. RS-232C Interface 4-3. Connectors and Signal Names 4-3-1. RS-232C InterfaceSERIAL Printer side 4-4. Interface ConnectionsSERIAL 4-5. Data Protocol 4-5-1. DTR modeError Condition 4-5-2. X-ON/X-OFF mode 5-2. Interface Timing 5-1. Interface Specifications5. PARALLEL INTERFACE PARALLEL 5-3. Connectors and Signal NamesFigure 5-1. Parallel Interface Connector goes LOW to trigger data read 6. PERIPHERAL UNIT DRIVE CIRCUIT Fastener One loop Ferrite core Screw M3×4 Separate ground wire Peripheral unit drive circuit connectorDrive circuit The recommended drive circuit is shown 7-2. Recoverable Errors Power Lamp Flashing On-Line 7. ERRORS7-1. Automatic Recovery Power Lamp Flashing On-Line Lamp On 7-3. Fatal Error Power Lamp Flashing On-Line Lamp Flashing 7-4. Type of buzzer sound only Star mode P 50ms Pi 100ms8. CONTROL CODES/STAR MODE 8-1. Star Mode Command SummaryCommands to Select Characters STAR MODE Commands to Set the Page FormatCommands to Move the Print Position Commands to Print Dot Graphics Commands to Print Download CharactersCommands to Control Peripheral Devices Commands to Control Auto CutterESC “?” LF NUL Other CommandsESC “#N, n1 n2 n3 n4” Select international character set 8-2. Command SpecificationCommands to Select Characters Page CODE 39, NW-7 automatically added at the beginning of the data STAR Control codesSpecial code Function codesSelect 12-dot pitch printing ESC “M” 1B 4D Sets the printing magnified double in character width SO 0E Sets the magnification rate in character height ESC “h” n 1B 68 n The part to be skipped by the horizontal tab setting is not reversed STAR MODE FUNCTIONCODE CODECommands to Set the Page Format Set left margin ESC “l” n 1B 6C n Commands to Move the Print Position length set by ESC“C” n or ESC“C”0 n when memory switchFeeds the paper to the top of the next page, according to the page Moves the print position to the next horizontal tab stop. Ignored ifPrints the current line and feeds the paper to the next vertical tab Page Set horizontal tab stops ESC “D” n1 n2 1B 44 n1 n2 Image data Commands to Print Dot GraphicsDOT Position We will create the design below using a bit image STAR MODEEXAMPLE Printing SamplePrint high density graphics STAR STAR MODE Image dataSTAR MODE EXAMPLEPrinting Sample LSB MSBPrint fine density graphics Commands to Print Download Characters Ignored 4 bitsPage Disable download character set ESC “%” “0” or ESC “%” 1B 25 30 or 1BFUNCTION CODECommands to Control Peripheral Devices Commands to Control Auto Cutter Other Commands Cancel last line & Initialize printerSet memory switch Always “0” Causes the printer to transmit a status byteStatus byte Resets the printer hardwareSTAR MODE FUNCTION9. CONTROL CODES/ESC/POS MODE ESC/POSDesignate the relative position of vertical characters when ESC/POS10. CHARACTER CODE TABLES Star ModeStar Mode Star Mode Character table katakanaPage International Character Set Star ModeESC/POS Mode ESC/POS Mode ESC/POS Mode Page 1KatakanaESC/POS Mode Page 2 PC850 MultilingualESC/POS Mode ESC/POS Mode Page 4 PC863 Canadian-FrenchESC/POS Mode ESC/POS Mode Page 255 Space PageESC/POS Mode 11. AUTOMATIC CUTTER MEMO P1996.11Page OVERSEAS SUBSIDIARY COMPANIES STAR MICRONICS AMERICA, INCSTAR MICRONICS DEUTSCHLAND GMBH ELECTRONIC PRODUCTS DIVISION