Manuals / Sterling / Household Appliance / Dehumidifier

Sterling SDF 250, SDF 400, SDF 500 manual Warnings and symbols

Models: SDF 500 SDF 250 SDF 400

1 72

Download 72 pages 16.54 Kb

Page 7

Image 7

SDF 250/400/500

1.1. Warnings and symbols

The following warnings and symbols are used in these operating instructions:

This symbol indicates danger to life! Fatal or serious injury is possible if the corresponding instructions, regulations or warnings are not observed.

LThis symbol indicates that serious injury is possible if the corresponding instructions, regulations or warnings are not observed.

FThis symbol indicates that extensive damage to equipment is possible if the corresponding instructions, regulations or warnings are not observed.

&This symbol indicates information important for becoming familiar with the equipment, i.e. technical correlations.

$This symbol indicates that a technical term is explained at this point.

General Information 1-2

Page 7

Image 7

Sterling SDF 250, SDF 400, SDF 500 manual Warnings and symbols

Contents

SDF SDF With Touch control unit Operating Instructions Dehumidified air dryer SDFSterling Material Processing 5200 West Clinton Ave Milwaukee, WI Technical service Service departmentSDF 250/400/500 Sterling Material ProcessingSDF 250/400/500 Table of contents SDF 250/400/500 General Information 1. General InformationSDF 250/400/500 1.1. Warnings and symbols Caution High noise pollution 1.5. Notes on Usage 1.2. Explanations and information1.3. Legal basis 1.4. Fields of applications2. Safety instructions Safety instructions 2.1. GeneralSDF 250/400/500 SDF 250/400/500 2.1.1. Assembly2.1.2. Operation Safety instructionsSafety instructions 2.1.3. MaintenanceSDF 250/400/500 Safety instructions 2.2. For the safety of the devicesSDF 250/400/500 3. Start up Start up 3.1. Control Unit3.1.1. Touch Screen SDF 250/400/500Start up 3.2. Switching on the DryerSwitch on the system by means of the main switch SDF 250/400/500Target value Actual value Status Dryer Basic parameters3.3.1. Entering Dryer Values Return air cooler on/orroptional SDF 250/400/500 3.3.2. Entering hopper valuesEnter hopper name Status Hopper Back to “Start-Screen”Page SDF 250/400/500 3.3.3. Setting the timerStart up Start up ”internal” = operation with internal timer”off” = operation without timer SDF 250/400/500Actual dew point temperature optional 3.3.4. Observing processing statusActual hopper temperature displayed in C Target hopper temperature displayed in CDate/Time Enter the desired day and time 3.3.5. Setting date and timeSDF 250/400/500 Start upStart up 3.3.6. Changing languageThis function is password protected SDF 250/400/500Start up SDF 250/400/5003.4.1.Continuous Operation of the Hopper 3.4. Continuous operation3.4.2.Continuous Operation of the Dryer Start up SDF 250/400/500Switch off the hopper heater Switch off the dryer 3.5. Switching the dryer/hopper heater offError and error correction 4. Error and error correctionSDF 250/400/500 Failures must be repaired immediately The Safety Switch Drying Blower Has Been Actuated 4.1. Actual messagesError and error correction PLC = SPS Battery is EmptyTemperature Measurement Outgoing Air Defective Error and error correctionError Bypass Flap Error Valve BlockTemperature Measurement Granules Defective Hopper Error and error correctionExcess Temperature Heater Hopper Insufficient Temperature Heater HopperOverload Drying Heater - STB has been activated Error and error correctionMain switch hopper heater # - Controller is off SDF 250/400/500Error and error correction 4.2. Alarm protocolSDF 250/400/500 5. Maintenance FPlease observe the maintenance schedule 5.1. Maintenance schedule 5.2. Cleaning or Replacing the Air Filter Maintenance Figure 0 SDF DryerSDF 250/400/500 SDF 250/400/500 Figure 1 SDF DryerMaintenance Install the cleaned/new air filter AFNever operate the dryer without filter mat 5.2.3. Filter of the electrical cabinetMaintenance SDF 250/400/5005.3. Disposing of Drying Agents 5.4. Cleaning the Drying Hopper Maintenance Figure 2 STTSDF 250/400/500 SDF 250/400/500 MaintenanceSTT 5.5. Changing the battery of the control system Order number battery 5.5.1. Resetting the control values Functional description 6. Functional descriptionSDF 250/400/500 FThe dryer is rated for continuous operation 6.1. General InformationDew point dependent regeneration switch optional SDF 250/400/500SDF 250/400/500 6.2. Drying Hopper Optional6.2.1. Hopper heaters optional Figure 3 Drying HopperFigure 4 Suction Box 6.4. Return Air Cooler OptionalTransport, Assembly and Storage 7. Transport, Assembly and StorageSDF 250/400/500 Figure 5 Transport with a fork lift truck 7.1. Tansport and PackingTransport, Assembly and Storage Figure 6 Transport with a workshop craneSDF 250/400/500 7.3. Storage 7.2. Assembly8. Assembly instructions Assembly instructions 8.2. Connection of Return Air Cooler OptionalSDF 250/400/500 8.3. Electrical Connection 8.4. Compressed Air Supply Basic Version 9. Technical dataTechnical data SDF 250/400/500Dimension Sheet Technical dataSDF 250/400/500 Accessories 10. AccessoriesSTT 25 - STT Spare parts list Drying Hoppers STT 25 - STT AccessoriesSterling Material Processing 5200 West Clinton Ave Milwaukee, WI Technical service Service departmentSTT 25 - STT Sterling Material ProcessingSTT 25 - STT STT 25 - STT Description STT 25 - STTDescription STT 25 - STT