INSTALLATION INSTRUCTIONS
INSTALLATION
IMPORTANT: ENSURE THAT THE APPLIANCE IS CORRECTLY ADJUSTED FOR THE GAS TYPE AND CATEGORY APPLICABLE IN THE COUNTRY OF USE. REFER TO DATABADGE AND TECHNICAL SPECIFICATIONS AT THE FRONT OF THIS BOOKLET.
FOR DETAILS OF CHANGING BETWEEN GAS TYPES REFER TO SECTION 11 PAGE 20.
1.CONTROL UPGRADE
1.1This stove is fitted with a control valve that can be easily upgraded to battery powered remote control. There are two versions of this control which can be obtained through your local Gazco stockist.
1.2This upgrade can be fitted before or after installation but if side clearances are limited then it will be easier to upgrade the stove before installation. Full instructions are included with the kit.
1.3STANDARD REMOTE CONTROL This remote control can control the gas appliance after the pilot has been lit. It can turn the main burner on and regulate it from low through to high and back again. It can turn the main burner off leaving the pilot burning. GAZCO PART NUMBER 8455.
1.4THERMOSTATIC AND TIMER REMOTE CONTROL This remote control can control the gas appliance after the pilot has been lit. In ‘MANUAL MODE’ it can be used to turn the main burner on and manually regulate it from low through to high and back again. It can also be used to turn the main burner off leaving the pilot burning. In ‘AUTO MODE’ it will automatically regulate the room temperature. In ‘TIMER MODE’ it will turn the fire on and off according to a
2.SAFETY PRECAUTIONS
2.1This appliance must be installed in accordance with the rules in force, and used only in a sufficiently ventilated space. Place read these instructions before installation and use of this appliance.
2.2All the instructions must be left intact with the user.
2.3In your own interest, and those of safety, this appliance must be installed by a competent person in accordance with local and national codes of practice. Failure to install the appliance correctly could lead to prosecution.
2.4This appliance is intended for use on a governed gas installation and set to the required pressure.
2.5Keep all plastic bags away from young children.
2.6Do not place any object on or near to the stove. Allow adequate clearance above the stove. See diagram 2 page 9.
2.7The stove is fitted with the Gazco Flue Sure System, which will act to cut off the gas supply to the appliance in the event of incorrect operation of the flue. If the system acts to shut off the gas supply, this indicates that there is insufficient flue pull. If this occurs a minimum of 10 minutes
should be allowed before trying to relight. Continued operation of this safety device means that there may be a serious problem with the flue system; a qualified gas engineer should inspect this. DO NOT USE THE STOVE
UNTIL AN ENGINEER SAYS IT IS SAFE TO DO SO.
2.8The Flue Sure System must not be tampered with. Use only genuine Gazco replacement parts when servicing the system - refer to servicing section on page 19.
3.INSTALLATION OF THE STOVE
3.1Open the carton, remove the accessory carton and stove unit. It will now be necessary to decide upon top or rear flue exit. The stove is factory built for rear flue exit but it may be changed to top exit by simply interchanging the flue spigot and blanking plate located on the stove.
3.2Position the stove ensuring all appropriate clearances are observed. Using a pencil, mark the position of the holes in the fixing brackets attached to the inside of the rear legs.
3.3Remove the stove and drill the holes using a number 12 masonry drill. Push rawlplugs into the holes and insert the woodscrews until the head is approximately 3mm proud of the hearth. Place the stove in position so that the screw heads located in the large part of the slot in the bracket, push the stove back so that the screw heads engage fully into the narrow part of the slot, tighten the screws if desired.
3.4Having run the gas supply to the stove, PURGE THE SUPPLY PIPE, this is essential to expel any debris that may block the gas controls. Connect the gas supply to the 8mm- compression elbow at the RH rear corner of the stove. There is a cutout in the RH rear leg to enable a direct straight connection to be made to the rear of the stove. See diagram 3. A gas soundness check must be completed up to the gas inlet connection.
3
AR0934
10
