USER INSTRUCTIONS
1.GENERAL
1.1Installation and servicing must be carried out by a competent person in accordance with Gas Safety (Installation and Use) Regulations 1998, the relevant British Standards for Installation, appropriate Codes of Practice and in accordance with the manufacturers instructions. It is recommended that a CORGI registered engineer be used for this purpose as they are approved by the HSE under the above regulations.
1.2This appliance is suitable for use in G.B. and I.E. using Natural Gas at a supply pressure of 20mbar or LPG at a supply pressure of 28mbar (Butane) or 37mbar (propane).
1.3The installation shall also be completed in accordance with:
The Building Regulations issued by The Department of The Environment.
The Building Standards (Scotland) Regulations issued by the Scottish Development Department.
For Republic of Ireland, reference should be made to the relevant standards governing installations (IS813:1996)
1.4Read all these instructions before commencing installation.
1.5This appliance must be installed in accordance with the rules in force and only used in a sufficiently ventilated space.
1.6Ensure that curtains are not positioned above the stove, and that there is at least a clearance of 300mm between the sides of the stove and any curtains.
1.7The manufacturer considers the full outer casing of this stove to be a working surface. Therefore it will become hot whilst in operation. A suitable guard is recommended to protect young children, the aged and the infirm.
1.8This stove must only be operated with the door secured firmly in position. If any cracks appear in the glass the appliance must not be used until the glass panel is replaced.
1.9Do not attempt to burn rubbish in this stove.
1.10Any combustible shelves or surrounding furniture must only be fitted in accordance with the minimum dimensions detailed in diagram 1.
1
1.11Contact a competent service engineer to carry out relevant spillage checks etc. following home improvements carried out after installation of this stove (e.g. the fitting of double glazing).
1.12In all correspondence, please quote the appliance type and serial number which can be found on the databadge at the rear of the stove.
1.13This product is guaranteed for 2 years from the date of installation, as set out in the terms and conditions of sale between Gazco and your local Gazco dealer. Please consult with your local Gazco dealer if you have any questions. In all correspondence always quote the model No. and serial No. Please ensure the commissioning checklist is completed by your installer, as this is a requirement of your Guarantee.
2.LIGHTING THE F40 AVANTI WITH HAND SET
2.1To ignite the F40 Avanti
The Gazco F40 Avanti has a fully automatic battery operated gas control which can be lit using the hand set or touch pad. The touch pad is located on the lower front panel of the appliance, behind the main door.
2 |
|
| 6 |
|
|
|
|
|
|
| 1: | Flame display | ||||
4 5 |
| 7 |
|
|
| 2: | Celsius display | |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 3: | Temperature display |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
8 |
|
|
|
|
|
|
|
|
|
| 1 | 4: | On display | |||
|
|
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| 5: | Off display | |
|
|
|
| 2 | ||||||||||||
9 |
|
|
|
| 6: | Low battery display | ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| 10 3 | 7: | Clock display | |||
12 |
|
|
|
|
|
| 8: | Auto display | ||||||||
|
|
|
|
| ||||||||||||
|
|
|
|
|
|
|
|
|
| 11 | 9: | Manual display | ||||
|
|
|
|
|
|
| ||||||||||
13 |
|
|
|
|
|
|
|
|
|
|
|
|
| 10: UP button | ||
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 11: ON/OFF button | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 12: SET button | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 13: DOWN button | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| AR1665 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2.1.1Before the fire can be lit the remote control must be in the manual mode. See diagram 2. Refer to section 2.6 to change to manual mode.
2.1.2Press the ON / OFF button (11). The word ON appears in the display (4).
2.1.3Press the SET button (12). The pilot light should now light. This should take about 10 seconds.
If the pilot fails to light press the ON / OFF button (11) and then the SET button (12) then repeat the above sequence.
2.1.4A single flame will appear on the display (1). When this has stopped flashing, an audible click is heard. You are now ready to adjust the flame height.
AR1468
4
