INSTALLATION INSTRUCTIONS

INSTALLATION

IAWARNING I

Shut-off power to the wall outlet.

Step 9

Unit is equipped with rollers. Plug into 15 amp grounded outlet and roll unit into desired position under the wood block or soffit and connect icemaker water line to unit. Remove garden hose fitting from plastic bag and attach the '/4" compression nut and sleeve on copper tubing before attaching the hose fitting to the solenoid valve. Purge line before final hookup to valve. See Figure

13.For Model 590 see

Figure 14.

Turn on water supply and check all fittings for leaks. Make certain electrical harness Is attached to solenoid.

NOTE: Icemaker will not immediately fill with water when supplied to valve. Allow 24 hours for proper ice production.

MODELS 511, 532, 542, 550, 561 AND501F

SOLENOID VALVE

Figure 13

MOOEL590

Figure 14

Step 10

Level the unit. To adjust height, turn front leveling legs counterclockwise to raise, or clockwise to lower. Rear levellers (rollers) are adjusted from front of base. Turn 5h6" hex bolt clockwise to raise cabinet, counterclockwise to lower cabinet. See Figure 12.

Step 11

Install toe plate as shown in Figure 15.

Before attaching toe plate check to ensure drain pan is installed properly.

IACAunON I

Toe plate must be removable for servicing, so any flooring must allow for this removal. Refer to label mounted on kickplate support for height clearance.

Step 12

Install grille, step 7.

IMPORTANT: For Models 511, 532, 542, 550, 561 and 590, reverse step 7 procedure. NOTE: If using panelized grille refer to "Grille Panel Installation. "

Step 13

Restore power to the wall outlet.

PANEL

INSTALLATION

Step 14

Apply decorative front panels (and side panels if applicable).

All Sub-Zero units are manufactured in a manner to achieve a total built-in appearance. This allows you to choose the decorative material and color application for the front and sides (if exposed) for your refrigeratorl freezer.

FRONT PANEL

INSTALLATION

(See "Pre-Installation Specifications" - for panel dimensions)

If a metal or other thin material is used, a filler must be in- serted behind your panel to insure a proper fit. All frames are designed to accept up to '/4" material. If a raised, wood front panel is being used, the edges must be routed to the necessary '/4" border specifi- cations. (50# per door panel maximum weight limit)

NOTE: ROUTING, RECESSING OR OP· TlONAL EXTENDED HANDLES MAY BE REQUIRED ON RAISED PANELS FOR FINGER CLEARANCE UNDER HANDLE. Refer to Figures 28 and 29 - "Handle Recess Specifications and Recommendation for Raised Panels."

NOTE: does not apply to Model 590.

MODELS 501F, 501R, 511, 532, 542, 550 AND 561

A)To install front panels on your Sub-Zero, the door handles must be removed. The handle screws are hidden by a magnet backed trim molidng. Remove the molding using a piece of tape to pull it away from the handle and expose the handle screws.

NOTE: the molding will bend at center allowing removal as in Figure 16.

Figure 15

5

Page 5
Image 5
Sub-Zero 590, 561 Panel Installation, Shut-off power to the wall outlet Step, Models 501F, 501R, 511, 532, 542, 550

550, 542, 561, 532, 511 specifications

Sub-Zero, a renowned name in luxury refrigeration, has long set the standard for high-performance refrigeration with its exceptional line of products, including models 590, 511, 532, 561, and 542. Each of these models showcases advanced features and cutting-edge technology designed to preserve food freshness while enhancing kitchen aesthetics.

The Sub-Zero 590 is a standout model known for its dual refrigeration system, which employs separate systems for the refrigerator and freezer compartments. This innovative approach allows for optimal humidity control and temperature management, preventing cross-contamination of odors and ensuring that perishables remain fresh for longer. Additionally, the 590 boasts a sleek design that can be seamlessly integrated into any kitchen decor.

Model 511 is designed with convenience in mind. Its compact design makes it an excellent choice for smaller kitchens or bar areas. This model continues the tradition of Sub-Zero's high standards, featuring advanced cooling technologies and smart storage solutions, such as adjustable shelving and door storage, maximizing usable space without compromising on performance.

The Sub-Zero 532 elevates the refrigeration experience with its advanced air purification system, which filters out particles and ethylene gas, a natural compound that accelerates ripening in fruits and vegetables. This ensures that your food stays fresher, longer, while preserving its nutritional quality. The model also includes features such as tempered glass shelves and LED lighting, providing both functionality and elegance.

The 561 model impresses with its built-in design, allowing for perfect integration into cabinetry for a custom look. This model offers a generous capacity while maintaining a sleek exterior. Furthermore, it includes advanced technology like a microprocessor control panel that monitors and adjusts temperatures, ensuring that your food is stored under ideal conditions.

Lastly, the Sub-Zero 542 showcases a classic built-in refrigerator/freezer configuration. Its signature design includes the option for a panel-ready finish, allowing homeowners to match it to their cabinetry. With features like smart touch controls and an advanced cooling system that maintains consistent temperatures, the 542 guarantees reliability and performance.

These Sub-Zero models represent the pinnacle of refrigeration technology, with features that prioritize freshness, convenience, and luxury aesthetics, making them a perfect addition to any modern kitchen.