INSTALLATION INSTRUCTIONS
B)With standard Phillips screwdriver, remove door handle on freezer and refrigerator door (the door handles also act as a door trim), The Models 511 and 550 freezer door handle isw on the top of the door and removed in the same manner described above,
C)Slide panel into frame on door as shown in Figure 17,•
IItllI'II'"nlllr/
MODEL 590
A)To install panels on the Model 590, the door handle and door handle trim must first be removed, The screws are hidden by a
NOTE: The trim molding will bend out at the center allowing removal as shown in Figure 16.
B)With standard Phillips screwdriver, remove door handles on freezer and refrig- erator doors (door handles also act as a door trim, see Figure 17),
C)Remove the handle trim panels by sliding them out of the door(s), See Figure 18,
NOTE: Different colored handle trim panels and glasswells are available through your product distributor.
D)Next, remove the water and ice glasswell by removing the mounting screw, Then slide the glasswell up and pull out as in Figure 18,
E)Remove the top and bottom trim fillers heid on by the mounting screw(s), See Figure 19,
F)Remove the screws holding in vertical trim strip, See Figure 19.
TRIMFILLEA
SCREWS
TRIM FILLER
SCREWS
GRILLE PANEL
INSTALLATION
If optional EA panel grille is purchased for Models 511 , 532 542,550 or 561, follow these instructions,
EA GRILLE PANEL SIZE
Grille Size | Panel Size |
10 x 30 | 8311. x 28311. |
11 x 30 | 9311. X 283116 |
12 x 30 | 103116 x 28311. |
13 x 30 | 113116 X 283116 |
14 x 30 | 12311. X 283116 |
15 x 30 | 133116 x 28311. |
10 x 36 | 83116 x 343116 |
11 x 36 | 93116 x 343116 |
12 x 36 | 103116 x 343116 |
13 x 36 | 11311. x 343116 |
14 x 36 | 123116 x 343116 |
15 x 36 | 133116 x 343116 |
10 x 42 | 83116 x 40311. |
11 x 42 | 93116 x 403116 |
12 x 42 | 10311. x 403116 |
13 x 42 | 113116 x 40311. |
14 x 42 | 123116 x 403116 |
15 x 42 | 133116 x 403116 |
10 x 48 | 83116 x 463116 |
11 x 48 | 9311. x 463116 |
12 x 48 | 103116 x 46311. |
13 x 48 | 11311. x 463116 |
14 x 48 | 123116 x 463116 |
15 x 48 | 133116 x 463116 |
D)With panel in position,
replace handle and screws, Replace the trim molding(s) by inserting the top and then the bottom into the handle channel. Release the middle and set the magnets,
GLASSWELL
SCRE:W
G)Install door panels by sliding into frame on door as shown in Figure 17,
H)With door panels in place, reverse the steps for proper reassembly,
NOTE: If replacing standard handle insert panels and glasswell with original or custom handle Insert panel or glasswell, refer to stepH.
The frame molding is de- signed to hold '/4 " thick panel. Raised wood panels must be routed to '/4 " thickness on all four sides to provide a '/4 " lip. (15Ibs, maximum panel weight.)
6