GENERAL INSTRUCTIONS

9

 

 

Slide out Bottom tray - Remove excess grease, then wash with warm soapy water, then rinse.

Flavorizer® bars and Cooking grates - Clean with a suitable stainless steel bristle brush. As needed, remove from grill and wash with warm soapy water, then rinse with water.

Catch pan - Disposable foil trays are available, or you can line the catch pan with aluminum foil. To clean the catch pan, wash with warm soapy water, then rinse.

Thermometer - Wipe with warm soapy water; clean with plastic scrub ball.

Inside cooking module - Brush any debris off of burner tubes. DO NOT ENLARGE BURNER PORTS (OPENINGS). Wash inside of cooking box with warm soapy water and a water rinse.

Inside Lid - While lid is warm, wipe inside with paper towel to prevent grease build-up. Flaking built-up grease resembles paint flakes.

Stainless steel surfaces - Wash with a soft cloth and a soap and water solution. Be careful to scrub with the grain direction of the stainless steel.

Do not use cleaners that contain acid, mineral spirits or xylene. Rinse well after cleaning.

Preserve Your Stainless Steel - Your grill or its cabinet, lid, control panel and shelves may be made from stainless steel. To keep the stainless steel looking its best is a simple matter. Clean it with soap and water, rinse with clear water and wipe dry. For stubborn particles, the use of a non-metallic brush can be used.

IMPORTANT: Do not use a wire brush or abrasive cleaners on the stainless steel surfaces of your grill as this will cause scratches.

IMPORTANT: When cleaning surfaces be sure to rub/wipe in the direction of the grain to preserve the look of your stainless steel.

GAS INSTRUCTIONS

INSTALL GAS SUPPLY

GENERAL SPECIFICATIONS FOR PIPING

Note: Contact your local municipality for building codes regulating outdoor gas barbecue installations. In absence of Local Codes, you must conform to the latest edition of the National Fuel Gas Code: ANSI Z 223.1/NFPA 54, or CAN/ CGA-B149.1, Natural Gas and Propane Installation Code. WE RECOMMEND THAT THIS

INSTALLATION BE DONE BY A PROFESSIONAL.

Some of the following are general requirements taken from the latest edition of the National Fuel Gas Code: ANSI Z 223.1/NFPA 54, or CAN/CGA-B149.1, Natural Gas and Propane Installation Code for complete specifications.

•This barbecue is designed to operate at 4.5 inches of water column pressure (.163 psi).

•A manual shut-off valve must be installed outdoors, immediately ahead of the quick disconnect.

•An additional manual shut-off valve indoors should be installed in the branch fuel line in an accessible location near the supply line.

•The quick disconnect connects to a ½ inch NPT thread from the gas source. The quick disconnect fitting is a hand-operated device that automatically shuts off the flow of gas from the source when the barbecue is disconnected.

•The quick disconnect fitting can be installed horizontally, or pointing downward. Installing the fitting with the open end pointing upward can result in collecting water and debris.

•The dust covers (supplied plastic plugs) help keep the open ends of the quick disconnect fitting clean while disconnected.

•Pipe compound should be used which is resistant to the action of natural gas when connections are made.

•The outdoor connector must be firmly attached to rigid, permanent construction.

WARNING: Do not route the 10 foot hose under a deck. The hose must be visible.

GAS LINE PIPING

•If the length of the line required does not exceed 50 feet, use a 5/8" O.D. tube. One size larger should be used for lengths greater than 50 feet.

•Gas piping may be copper tubing, type K or L; polyethylene plastic tube, with a minimum wall thickness of .062 inch; or standard weight (schedule 40) steel or wrought iron pipe.

•Copper tubing must be tin-lined if the gas contains more than 0.3 grams of hydrogen sulfide per 100 cubic feet of gas.

•Plastic tubing is suitable only for outdoor, underground use.

•Gas piping in contact with earth, or any other material which may corrode the piping, must be protected against corrosion in an approved manner.

•Underground piping must have a minimum of 18" cover.

TEST CONNECTIONS

All connections and joints must be thoroughly tested for leaks in accordance with local codes and all listed procedures in the latest edition of the National Fuel Gas Code: ANSI Z 223.1/NFPA 54, or CAN/CGA-B149.1

DANGER

Do not use an open flame to check for gas leaks. Be sure there are no sparks or open flames in the area while you check for gas leaks. This will result in a fire or explosion which can cause serious bodily injury or death and damage to property.

WWW.WEBER.COM®

Page 8 Page 10
Page 9
Image 9
Summit E/S-420/450 manual GAS Instructions, Install GAS Supply, General Specifications for Piping, GAS Line Piping
Page 8 Page 10

E/S-420/450 specifications

The Summit E/S-420/450 is a cutting-edge electric scooter that redefines urban mobility with its innovative features and advanced technologies. Designed for both efficiency and performance, this model caters to the needs of daily commuters and recreational riders alike.

One of the standout features of the Summit E/S-420/450 is its impressive range. With a high-capacity lithium-ion battery, riders can travel up to 50 miles on a single charge, making it suitable for longer journeys without the worry of running out of power. Its quick charging capability allows the battery to be replenished in just a few hours, ensuring minimal downtime.

Powering the scooter is a robust brushless motor that offers a top speed of 28 mph. This powerful motor not only provides an exhilarating ride but also excellent acceleration, allowing riders to merge into traffic confidently. The motor is paired with an efficient regenerative braking system, which helps to conserve energy by converting some of the kinetic energy back into battery power during braking.

The frame of the Summit E/S-420/450 is crafted from lightweight yet durable materials, ensuring a sturdy ride without compromising on maneuverability. The ergonomically designed handlebars and comfortable seat provide additional comfort for long commutes. The scooter also features an adjustable suspension system that absorbs bumps and ensures a smooth ride on various terrains.

Safety is a significant consideration in the design of the Summit E/S-420/450. It comes equipped with front and rear LED lights for increased visibility, as well as reflective strips on the body. The anti-lock braking system (ABS) ensures that riders can stop quickly and safely in emergency scenarios.

In terms of technology, the Summit E/S-420/450 boasts a user-friendly LCD display that provides real-time information on speed, battery level, and distance traveled. Bluetooth connectivity allows users to sync their devices, making it possible to receive navigation and call alerts while riding.

Overall, the Summit E/S-420/450 stands out in the crowded electric scooter market, combining range, speed, comfort, and safety in a sleek, stylish package. Whether for commuting to work or enjoying a weekend ride, this electric scooter offers an unmatched experience for riders looking for efficiency and fun in their daily travels. With its advanced features and technologies, the Summit E/S-420/450 is a significant step forward in personal transportation, promoting a sustainable future for urban mobility.
Top Page Image Contents