Sun Microsystems 9740 Expansion Door Procedure

Operating in Manual Mode

3-28 Revision P 95693

5. Turn the reach mechanism drive belt until the gripper is fully retracted.

6. If a cartridge was in the top cell, re-insert it properly into the cell.

Expansion Door Procedure

To remove a cartridge from the hand when your LSM has an expansion door:

1. Rotate the Z column until the hand is facing the expansion door location.

2. Rotate the reach mechanism belt drive until the gripper is extended to its full

position, as shown in Figure 3-15 on page 3-28.

3. Hold the reach mechanism belt drive with one hand and grasp the cartridge with the

other. Pull gently on the cartridge until it is released from the gripper, as shown in

Figure 3-16 on page 3-29.

CAUTION:

Potential equipment damage: Make sure that the gripper is fully

retracted. If it is left extended and you turn the robot, the gripper will

strike a storage cell. If it is left extended and the hand is facing the LSM

door when it is closed, the door will strike the gripper.

4. Turn the reach mechanism belt drive until the gripper is fully retracted.

Figure 3-15. Extending the Gripper (C62026)

C6202

6

REACH

MECHANISM

BELT

DRIVE

TAPE

CARTRIDGE

(SHOWN

RETRACTED)

Contents

Main Page Page ii Revision P 95693 Summary of Changes Page Contents Page Page Figures Tab le s Page Preface Page Suns External Web Site Customer Resource Center Partne rs Site Hardcopy Publications Page Notices Page 95693 Revision P xvii The following is the Internal Code License Agreement from Sun StorageTek: xviii Revision P 95693 General Information Robot Page Cartridge Access Port Storage Cells Cartridge Exchange Mechanism Page Page Controls and Indicators Tape Drives and Cabinets Controller Transport Units Page Figure 2-3. Operator Panel Function Keys, Indicators, and Displays (C62014) 95693 Revision P 2-5 Setting the SCSI Address Figure 2-4. Symbol Definitions for Menu Block Diagram (C62015) Symbol Definitions for Menu Block Diagrams How Used.... Setting the SCSI Address 2-6 Revision P 95693 Figure 2-5. Setting the SCSI Address (C62016) Operating the LSM Loading Cartridges through the CAP Page Ejecting Cartridges through the CAP SCSI Interface AUTO CLEAN Feature Cleaning Drives in the LSM 3-6 Revision P 95693 Setting the Cleaning Cartridge Usage Count Q Replacing Cleaning Cartridges Serial Interface Setting the Cleaning Cartridge Usage Count Replacing Cleaning Cartridges Unlocking the CAP and Removing Non-cleaning Cartridges Replacing Expired Cleaning Cartridges Opening the LSM Front Doors Figure 3-3. Opening Front Doors (C62021) Moving the Robot Raising and Lowering the Z Carriage Rotating the Z Column Locating a Cartridge in the Storage Cells 9740 with Expansion Door 95693 Revision P 3-15 Figure 3-7. Locating CartridgesPanels, Cells, Rows, Cartridge Drive (C62013) 3-16 Revision P 95693 Figure 3-8. Locating CartridgesPanels, Cells, Rows, Drive Cabinet (C62377) 95693 Revision P 3-17 Figure 3-9. Locating CartridgesPanels, Cells, Rows, CEM (C62524) Page Mounting and Dismounting Cartridge Tapes Mounting a Cartridge into a 9490 or SD-3 CTU Dismounting a Cartridge from a 9490 or SD-3 CTU 95693 Revision P 3-21 Mounting a Cartridge into a DLT Drive Page Dismounting a Cartridge from a DLT Drive Mounting a Cartridge into a T9840 Drive Dismounting a Cartridge from a T9840 Drive Mounting a Cartridge into a T9940 Drive Dismounting a Cartridge from a T9940 Drive Removing a Cartridge from the Hand Standard Door Procedure Expansion Door Procedure Returning the LSM Online Page Drives 9490 SD-3 Power Switch Operator Panel Page Digital Linear Tape Drives T9840 and T9940 Tape Drives 9741/9741E Drive Cabinet 4-6 Revision P 95693 Figure 4-4 is an example of the operator panel: Figure 4-4. T9840/T9940 Operator Panel Service Page A Cartridge Tape Information Page 95693 Revision P A-3 Inspecting a Cartridge Figure A-2. Inspecting an SD-3 Helical Scan Cartridge Figure A-3. Inspecting a DLT Cartridge Inspecting a Cartridge A-4 Revision P 95693 Figure A-4. Inspecting a T9840 Cartridge (C62715) FRONT VIEW REAR VIEW REAR VIEW Figure A-5. Inspecting a T9940 Cartridge (C62727) Page Page Non-DLT Cartridges Figure A-6. 3480 Cartridge Label Locations (C62031) Figure A-7. ETape Cartridge Label Locations (C62528) 95693 Revision P A-9 Applying Labels Figure A-8. EETape Cartridge Label Locations (C62526) Figure A-9. Helical Scan Cartridge Label Locations (C62032) Applying Labels A-10 Revision P 95693 Figure A-10. T9840 Cartridge Label Locations (C62444) Figure A-11. T9940 Cartridge Label Location (C62731) DLT Cartridges 9490 Write-Protect Switch 95693 Revision P A-13 Setting the Write-Protect Switch Figure A-14. Setting the ETape Write-Protect Selector (C62529) Figure A-15. Setting the EETape Write-Protect Selector (C62523) SD-3 Write-Protect Switch DLT Write-Protect Switch T9840 Write-Protect Switch T9940 Write-Protect Switch Page Page Page Glossary Numeric A C D I O L M R S T V Z Page Index Numerics A C D E F G H M N O P R U V W Z Page SUN United States and other countries.