Sata Drive Carrier LEDs | SUPER MICRO Computer 5015M-UR, 5015M-NT

Chapter 3: System Interface

2

NIC2: Indicates network activity on LAN2 when ﬂ ashing .

1

NIC1: Indicates network activity on LAN1 when ﬂ ashing.

HDD: Indicates IDE channel activity. On the SuperServer 5015M-UR/ 5015M-U/5015M-NTR/5015M-NT this light indicates SATA and/or DVD-ROM drive activity when ﬂ ashing.

Power: Indicates power is being supplied to the system's power supply units. This LED should normally be illuminated when the system is operating.

3-4 SATA Drive Carrier LEDs

Each Serial ATA drive carrier has two LEDs.

Green: When illuminated, the green LED on the front of the SATA drive car- rier indicates drive activity. A connection to the SATA backplane enables this LED to blink on and off when that particular drive is being accessed.

Red: The red LED indicates two states. When blinking, it indicates the drive is rebuilding. When solid, it indicates a drive failure. If a SATA drive fails, you should be notiﬁ ed by your system management software. Please refer to Chapter 6 for instructions on replacing failed SATA drives.

3-3

Image 29

SUPER MICRO Computer 5015M-UR, 5015M-NTR user manual Sata Drive Carrier LEDs

Contents

Super Manual Revision 1.0c Release Date September 10 Manual Organization PrefaceAbout This Manual Advanced Serverboard Setup System SafetyAdvanced Chassis Setup Bios Preface Table of Contents Advanced Serverboard Setup System Safety Bios Advanced Chassis Setup Appendices Page Overview Chapter Introduction Processors Serverboard FeaturesMemory UIO 5015M-UR Server Chassis Features Front Control Panel PCI Expansion SlotsBackplane Cooling System Intel 3010 Chipset System Block Diagram Headquarters Contacting SupermicroEurope Asia-Paciﬁc Unpacking the System Chapter Server InstallationPreparing for Setup Server Precautions Choosing a Setup LocationRack Precautions Rack Mounting Considerations Identifying the Sections of the Rack Rails Installing the System into a RackInstalling the Inner Rails Locking Tabs Installing the Outer Rails Installing the Server into a Rack Installing the Server into the Rack Installing the Server into a Telco Rack Installing the Server into a Telco Rack Checking the Serverboard Setup Accessing the Inside of the System Checking the Drive Bay Setup Control Panel Buttons Chapter System Interface Universal Information LED States Control Panel LEDs Sata Drive Carrier LEDs Page Electrical Safety Precautions Chapter System Safety General Safety Precautions ESD Precautions Installing the Onboard Battery Operating Precautions Precautions Chapter Advanced Serverboard SetupHandling the Serverboard Unpacking Installing the Processor Processor and Heatsink InstallationPage Removing the Heatsink Installing the Heatsink Connecting Power Cables Connecting CablesConnecting Data Cables Front Control Panel Header Pins JF1 Connecting the Control Panel I/O Ports Installing MemoryDimm Installation Memory Support Installing Dimm into Slot PCI Expansion Slots PCI card installationAdding PCI Cards Super Pdsmu Layout Serverboard Details Connector Description Jumper Description Default SettingPdsmu Quick Reference LEDs Description ATX Power Connector Connector DeﬁnitionsProcessor Power Connector Power LED Universal Information LED HDD LED Reset Button Power Fail LEDPower Button Universal Serial Bus USB0/1 Fan Headers Universal Serial Bus HeadersSerial Ports Chassis Intrusion Speaker ConnectorATX PS/2 Keyboard and PS/2 Mouse Ports Wake-On-LAN Power Supply Fail Power SMB I2C ConnectorAlarm Reset JAR Wake-On-Ring LAN1/2 Ethernet Ports VGA Enable/Disable Jumper SettingsExplanation Jumpers Cmos Clear Power Force On Enable/ Disable LAN Enable/DisableWatch Dog Enable/Disable LAN1/LAN2 LEDs Onboard Indicators Floppy, IDE and Sata Drive Connections Floppy Connector Sata Ports IDE ConnectorPage Tools Required Chapter Advanced Chassis SetupStatic-Sensitive Devices Chassis Front and Rear Views Control Panel System Fans Installing a new fanSystem Fan Failure Replacing System Fans Removing the Front Bezel Drive Bay Installation/Removal Removing the Front Bezel Accessing the Drive Bays Mounting a Sata drive in a drive carrier Sata Drive Installation Removing a Sata Drive from the Server Installing/removing hot-swap Sata drives DVD-ROM and Floppy Drive Installation Power Supply Failure Power SupplyRemoving/Replacing the Power Supply 5015M-UR/5015M-NTR 5015M-U/5015M-NT Removing/Replacing the Power Supply Page How To Change the Conﬁguration Data System BiosStarting the Setup Utility Chapter Press the Delete key to enter Setup Running SetupMain Bios Setup Main Bios Setup Menu Main Setup Features Sata Controller Mode Native Mode OperationSerial ATA Sata RAID Enable ICH RAID Code Base Available when Sata RAID is Enabled Transfer Mode LBA Mode ControlUltra DMA Mode Type Advanced Setup Memory Cache Cache System Bios Area Power Loss ControlCache Video Bios Area Resume On Modem Ring Cache Base 512K-640K Reset Conﬁguration DataCache Extended Memory Discrete Mtrr Allocation Latency Timer Enable MasterLarge Disk Access Mode Clock Spectrum Feature Legacy USB Support USB FunctionAdvanced Processor Options CPU Speed Set Maximum Extended CPUID=3 C1 Enhanced Mode Available when supported by the CPUDevice Conﬁguration KBC Clock Input Base I/O Address Serial Port aInterrupt Serial Port B Event Log Validity DMI Event LoggingEvent Log Capacity View DMI Event Log COM Port Address Console RedirectionBaud Rate Console Type Hardware Monitor Logic CPU Temperature ThresholdVoltage Monitoring Fan Speed Control Modes User Password Is Supervisor Password IsSet Supervisor Password Set User Password Boot Priority Order/Excluded from Boot Orders BootPassword on Boot Exit Appendix a Bios Post Messages System timer error System Cmos checksum bad Default conﬁguration usedReal time clock error Check date and time settings Fail-Safe Timer NMI Failed System cache error Cache disabledAllocation Error for device Entering Setup Invalid System Conﬁguration Data PS/2 Mouse Boot Summary ScreenDevice IRQ conﬂict Nnnn kB Extended RAM Passed Press F2 to enter Setup Press F1 to resume, F2 to Setup, F3 for previousSystem Bios shadowed Video Bios shadowedPage Recoverable Post Errors Appendix B Bios Post CodesTerminal Post Errors Post Code Description Post Code Description Post Code Description Post Code Description Following are for boot block in Flash ROM Page Introduction to Serial ATA and Parallel ATA Intel HostRAIDImportant Notes to the User Serial ATA Sata Intel Matrix Storage RAID Conﬁgurations Using the Intel ICH7R Sata RAID Utility Program Creating a RAID 0 Volume Creating a RAID 1 Volume Creating a RAID 10 RAID 1+ RAID Creating a RAID 5 Set Parity Deleting a RAID Volume Exiting the Intel Matrix Storage Manager Utility Resetting to Non-RAID and Resetting a RAID HDD New Operating System-Windows XP/2000/2003 Installation Installing Windows XP/2000/2003 for RAID Systems Introduction to the Intel ICH7R I/O Controller Hub Appendix D Adaptec HostRAID Setup Guidelines Conﬁguring the Adaptec Sata RAID Adaptec Embedded Sata with HostRAID Controller Driver Using the Adaptec RAID Conﬁguration Utility ARCUsing the Array Conﬁguration Utility ACU Managing Arrays To conﬁgure a disk drive Conﬁguring Disk DrivesPage Page To create an array Creating Arrays To assign properties to the new array Assigning Array PropertiesPage Deleting a Bootable Array Adding a Bootable Array Adding/Deleting Hotspares Viewing Array Properties To Rebuild an array Rebuilding Arrays RAID 1 only-the following prompt is also displayed Deleting Arrays To access the disk utilities Using the Disk Utilities To format a disk To verify disk media To Exit the Adaptec RAID Conﬁguration Utility Installing the Adaptec ICH7R Driver and the OS Appendix E System Speciﬁcations Power Supply WeightServerboard Chassis Regulatory Compliance Operating Environment