LAN1/2 Ethernet Ports, Power LED | SUPER MICRO Computer 5015M-NT

SUPERSERVER 5015M-UR/5015M-U/5015M-NTR/5015M-NT User's Manual

LAN1/2 (Ethernet Ports)

Two Ethernet ports (designated LAN1 and LAN2) are located beside the VGA port on the I/O backplane. These ports accept RJ45 type cables.

Power LED

The Power LED connector is desig- nated JLED. Connect an LED here for indication of power being supplied to the serverboard. See the table on the right for pin deﬁ nitions.

Power LED

Pin Deﬁnitions (JLED)

Pin# Deﬁ nition

1+5V

2Key

3Ground

5-18

Image 52

SUPER MICRO Computer 5015M-UR, 5015M-NTR user manual LAN1/2 Ethernet Ports, Power LED

Contents

Super Manual Revision 1.0c Release Date September 10 About This Manual PrefaceManual Organization System Safety Advanced Serverboard SetupAdvanced Chassis Setup Bios Preface Table of Contents System Safety Advanced Serverboard Setup Advanced Chassis Setup Bios Appendices Page Chapter Introduction Overview Serverboard Features ProcessorsMemory UIO 5015M-UR Server Chassis Features PCI Expansion Slots Front Control PanelBackplane Cooling System Intel 3010 Chipset System Block Diagram Contacting Supermicro HeadquartersEurope Asia-Paciﬁc Preparing for Setup Chapter Server InstallationUnpacking the System Rack Precautions Choosing a Setup LocationServer Precautions Rack Mounting Considerations Installing the Inner Rails Installing the System into a RackIdentifying the Sections of the Rack Rails Installing the Outer Rails Locking Tabs Installing the Server into the Rack Installing the Server into a Rack Installing the Server into a Telco Rack Installing the Server into a Telco Rack Checking the Serverboard Setup Accessing the Inside of the System Checking the Drive Bay Setup Chapter System Interface Control Panel Buttons Control Panel LEDs Universal Information LED States Sata Drive Carrier LEDs Page Chapter System Safety Electrical Safety Precautions General Safety Precautions ESD Precautions Operating Precautions Installing the Onboard Battery Chapter Advanced Serverboard Setup PrecautionsHandling the Serverboard Unpacking Processor and Heatsink Installation Installing the ProcessorPage Installing the Heatsink Removing the Heatsink Connecting Data Cables Connecting CablesConnecting Power Cables Connecting the Control Panel Front Control Panel Header Pins JF1 Dimm Installation Installing MemoryI/O Ports Installing Dimm into Slot Memory Support Adding PCI Cards PCI card installationPCI Expansion Slots Serverboard Details Super Pdsmu Layout Jumper Description Default Setting Connector DescriptionPdsmu Quick Reference LEDs Description Connector Deﬁnitions ATX Power ConnectorProcessor Power Connector Power LED HDD LED Universal Information LED Power Fail LED Reset ButtonPower Button Universal Serial Bus USB0/1 Serial Ports Universal Serial Bus HeadersFan Headers Speaker Connector Chassis IntrusionATX PS/2 Keyboard and PS/2 Mouse Ports Wake-On-LAN Power SMB I2C Connector Power Supply FailAlarm Reset JAR Wake-On-Ring LAN1/2 Ethernet Ports Jumper Settings VGA Enable/DisableExplanation Jumpers Cmos Clear Watch Dog Enable/Disable LAN Enable/DisablePower Force On Enable/ Disable Onboard Indicators LAN1/LAN2 LEDs Floppy Connector Floppy, IDE and Sata Drive Connections IDE Connector Sata PortsPage Static-Sensitive Devices Chapter Advanced Chassis SetupTools Required Control Panel Chassis Front and Rear Views Installing a new fan System FansSystem Fan Failure Replacing System Fans Drive Bay Installation/Removal Removing the Front Bezel Accessing the Drive Bays Removing the Front Bezel Sata Drive Installation Mounting a Sata drive in a drive carrier Installing/removing hot-swap Sata drives Removing a Sata Drive from the Server DVD-ROM and Floppy Drive Installation Power Supply Power Supply FailureRemoving/Replacing the Power Supply 5015M-UR/5015M-NTR 5015M-U/5015M-NT Removing/Replacing the Power Supply Page System Bios How To Change the Conﬁguration DataStarting the Setup Utility Chapter Main Bios Setup Running SetupPress the Delete key to enter Setup Main Bios Setup Menu Main Setup Features Native Mode Operation Sata Controller ModeSerial ATA Sata RAID Enable ICH RAID Code Base Available when Sata RAID is Enabled LBA Mode Control Transfer ModeUltra DMA Mode Type Advanced Setup Power Loss Control Memory Cache Cache System Bios AreaCache Video Bios Area Resume On Modem Ring Reset Conﬁguration Data Cache Base 512K-640KCache Extended Memory Discrete Mtrr Allocation Enable Master Latency TimerLarge Disk Access Mode Clock Spectrum Feature USB Function Legacy USB SupportAdvanced Processor Options CPU Speed C1 Enhanced Mode Available when supported by the CPU Set Maximum Extended CPUID=3Device Conﬁguration KBC Clock Input Serial Port a Base I/O AddressInterrupt Serial Port B DMI Event Logging Event Log ValidityEvent Log Capacity View DMI Event Log Console Redirection COM Port AddressBaud Rate Console Type CPU Temperature Threshold Hardware Monitor LogicVoltage Monitoring Fan Speed Control Modes Supervisor Password Is User Password IsSet Supervisor Password Set User Password Password on Boot BootBoot Priority Order/Excluded from Boot Orders Exit Appendix a Bios Post Messages System Cmos checksum bad Default conﬁguration used System timer errorReal time clock error Check date and time settings System cache error Cache disabled Fail-Safe Timer NMI FailedAllocation Error for device Entering Setup PS/2 Mouse Boot Summary Screen Invalid System Conﬁguration DataDevice IRQ conﬂict Nnnn kB Extended RAM Passed Press F1 to resume, F2 to Setup, F3 for previous Press F2 to enter SetupSystem Bios shadowed Video Bios shadowedPage Appendix B Bios Post Codes Recoverable Post ErrorsTerminal Post Errors Post Code Description Post Code Description Post Code Description Post Code Description Following are for boot block in Flash ROM Page Intel HostRAID Introduction to Serial ATA and Parallel ATAImportant Notes to the User Serial ATA Sata RAID Conﬁgurations Intel Matrix Storage Using the Intel ICH7R Sata RAID Utility Program Creating a RAID 0 Volume Creating a RAID 1 Volume Creating a RAID 10 RAID 1+ RAID Creating a RAID 5 Set Parity Deleting a RAID Volume Resetting to Non-RAID and Resetting a RAID HDD Exiting the Intel Matrix Storage Manager Utility Installing Windows XP/2000/2003 for RAID Systems New Operating System-Windows XP/2000/2003 Installation Appendix D Adaptec HostRAID Setup Guidelines Introduction to the Intel ICH7R I/O Controller Hub Conﬁguring the Adaptec Sata RAID Using the Array Conﬁguration Utility ACU Using the Adaptec RAID Conﬁguration Utility ARCAdaptec Embedded Sata with HostRAID Controller Driver Managing Arrays Conﬁguring Disk Drives To conﬁgure a disk drivePage Page Creating Arrays To create an array Assigning Array Properties To assign properties to the new arrayPage Adding a Bootable Array Deleting a Bootable Array Adding/Deleting Hotspares Viewing Array Properties Rebuilding Arrays To Rebuild an array Deleting Arrays RAID 1 only-the following prompt is also displayed Using the Disk Utilities To access the disk utilities To format a disk To verify disk media To Exit the Adaptec RAID Conﬁguration Utility Installing the Adaptec ICH7R Driver and the OS Appendix E System Speciﬁcations Weight Power SupplyServerboard Chassis Operating Environment Regulatory Compliance